Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• The removable parts of the burners should be washed frequently with warm water and soap, making sure to remove caked-on substances. • On hobs with automatic ignition, the end of the electronic ignition device must be cleaned carefully and frequently, making sure that the gas holes are not clogged. • Stainless steel can be stained if it remains in contact with highly calcareous water or aggressive detergents (containing phosphorous) for an extended period of time. It is recommended that these parts be rinsed thoroughly with water and then dried well. It is also a good idea to clean up any spills. Greasing the Gas Valves Over time, the gas valves may stick or become difficult to turn. If this is the case, the must be cleaned on the inside and the regreased. N.B.: This procedure must be performed by a technician authorized by the manufacturer. Troubleshooting Before calling service for assistance, check through the following list, there may be nothing wrong. First of all, check to see that there are no interruptions in the gas and electrical supplies, and, in particular, that the gas valves for the mains are open. If the burner does not light or the flame is not uniform around the burner. Check to make sure that: • The gas holes on the burner are not clogged. • All of the movable parts that make up the burner are mounted correctly. • There are no draughts around the cooking surface. If the flame does not stay lit on a model with the Flame Failure device. Check to make sure that: • You press the knob all the way in. • You keep the knob pressed in long enough to activate the flame failure device. • The gas holes are not clogged in the area corresponding to the flame failure device. If the burner does not remain on when set to "Low". Check to make sure that: • The gas holes are not clogged. • There are no draughts near the cooking surface. • The minimum has been adjusted correctly (see Installation section, "Minimum Regulation"). If the cookware is not stable. Check to make sure that: • The bottom of the cookware is perfectly flat. • The cookware is centered correctly on the burner . • The support grids have not been inverted. If, despite all of these checks, the hob does not function properly and problem persists, call Hotpoint Service (see KEY CONTACTS, back page), informing them of: -The type of problem. -The abbreviation used to identify the model (Mod. ...) as indicated on the warranty. IMPORTANT: Never call upon technicians not authorized by the manufacturer, and refuse to accept spare parts that are not original. 7 Installation The following instructions are intended for the installer so that the installation and maintenance procedures may be followed in the most professional and expert manner possible. Important: Disconnect the appliance from the electrical supply before performing any maintenance or repair. Positioning the Hob Important: this unit may be installed and used only in permanently ventilated rooms in accordance with British Standard Codes Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891 Current Editions.The following requirements must be observed: a) The room must be fitted with a ventilation system which vents smoke and gases from combustion to the outside.This must be done by means of a hood or electric ventilator that turns on automatically each time the hob is operated. In a chimney stack or branched flue. Directly to the Outside(exclusively for cooking appliances) b)The room must have an air flow to allow for proper combustion. This must be 2 m3./h per kW of installed power. The airflow can be created using an enclosed vent with an inner cross section of at least 100 cm. which must not be able to be blocked. I the appliance does not have a flame failure device, the vent must have an internal cross section of 200 cm3. (Fig. A). Alternatively the room in which the hob is situated can be vented indirectly through ventilation ducts as specified above, as long as the adjacent room is not a shared area, a bedroom or present any risk of fire (Fig. B). Detail A Adjacent Room to be d) Liquidified petroleum gases are heavier than air and, as a result, settle downwards. Rooms in which LPG tanks are installed must be fitted with ventilation openings to the outside in order to allow the gas to escape in the event of a leak. Therefore, LPG tanks, whether empty or partially full, must not be installed or stored in rooms or spaces below ground level (cellars, ect.). It is also a good idea to keep only the tank currently being used in the room, making sure that it is not near sources of heat (ovens, fireplaces, stoves, etc.) that could raise the internal temperature of the tank above 50°C. Installation of Built-in Hobs The gas hob is equipped with type X degree protection against overheating. Therefore, the appliance can be installed next to cabinets, provided the height of the cabinet does not exceed that of the hob. For proper installation of the hob, the following guidlines must be followed:...
Dieses Handbuch ist für folgende Modelle:Kochfelder - S830G (398.1 kb)