Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Color Temp Right-Adjustment selects the color temperature to the right and Left-Adjustment selects the color temperature to the left. Reset This control resets the monitor to factory default values. Exit This control exits the OSD menu. 4–4 Reference Guide Operation Monitor Messages No Signal Message If a No Signal message displays on your monitor, check to be sure your video cable is properly connected and ensure that your computer is powered on. Out of Frequency Range Message If an Out of Frequency Range message displays on your monitor, your video resolution and/or refresh rate are set higher than the levels your monitor supports. To change the video resolution or refresh rate on your monitor, follow these steps: 1. Restart your computer. 2. Enter Safe Mode on your computer. Refer to your computer’s operating system Help for instructions on entering Safe Mode. Reference Guide 4–5 Operation 3. Change your display settings to a supported setting (see “Technical Specifications”). 4. Restart your computer so that the new settings take effect. Using the Energy Saver Mode Your monitor is designed to meet strict Environmental Protection Agency (EPA) Energy Star requirements for reduced power consumption. Using a combination of hardware and software functions, this energy-saving feature allows your computer to control your monitor’s power consumption and reduce your monitor’s power state when not in use. Power Management Status for 5500/15” Series Monitors (CV, MV, S) LED Power State Color Consumption Description On Green < 80 watts Normal Operation Sleep Amber < 5 watts Monitor screen is blank. High voltage is off. Heater voltage is off. There is a brief warm-up period before returning to full power mode. Power Management Status for 7500 and 7550/17” Series Monitors (CV, MV,S,FS, V) LED Power State Color Consumption Description On Green < 100 watts Normal Operation Sleep Amber < 5 watts Monitor screen is blank. High voltage is off. Heater voltage is off. There is a brief warm-up period before returning to full power mode. Power Management Status for 9500/19” Series Monitors (MV, S) LED Power State Color Consumption Description On Green < 130 watts Normal Operation Sleep Amber < 5 watts Monitor screen is blank. High voltage is off. Heater voltage is off. There is a brief warm-up period before returning to full power mode. 4–6 Reference Guide Operation . . Your monitor’s energy saver feature works only when your monitor is connected to a computer that also has energy saver features. The Energy Saver utility, with its energy saving features, is available with all Microsoft Windows operating systems. Some features are also available in DOS. Refer to your computer’s user guide for instructions on setting energy saver features (also referred to as power management features). Reference Guide 4–7 A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Power switch is off. Turn on power. Video cable is improperly connected. Connect video cable properly. Screen blanking utility is active. Depress any key on the keyboard or move the mouse. Image appears blurred, indistinct, or too dark. Brightness and contrast are too low. Press the SELECT button to access the On-Screen Display. Select the Brightness and/or Contrast icons to adjust as needed. Color is abnormal. A magnetic object may be nearby. Monitor may have been moved or inadvertently bumped. Move the object farther away. Press the SELECT button to access the On-Screen Display. Select Degauss to activate. Compaq suggests you not degauss more than once within a 30-minute period of time. Image is too large or too small. Horizontal width may need adjustment. Vertical height may need adjustment. Press the SELECT button to access the On-Screen Display. Select H. Size to adjust as needed. Press the SELECT button to access the On-Screen Display. Select V. Size to adjust as needed. Image is not centered. Horizontal position may need adjustment. Press the SELECT button to access the On-Screen Display. Select H. Position to adjust as needed. Reference Guide A–1 Problem Possible Cause Solution Vertical position may need adjustment. Press the SELECT button to access the On-Screen Display. Select V. Position to adjust as needed. “No Signal” is displayed on screen. Monitor video cable is disconnected. Connect the 15-pin monitor video cable to the computer. Be sure that the computer power is on. “Out of Frequency” is displayed on screen. Video resolution and/or refresh rate are set higher than what your monitor supports. Restart your computer and enter Safe Mode. Change your settings to a supported setting (see “Technical Specifications”). Restart your computer so that the new settings take effect. No speaker power. Speaker power cord is disconnected. Check all speaker power connections a...
Dieses Handbuch ist für folgende Modelle:Monitore - 7550 (174.63 kb)
Monitore - 9500 (174.63 kb)