Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Performance is maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper towel to wipe the edge of the belt and the area between the belt edge and frame. Also reach as far as practical directly under the belt edge. This should be done once a month to extend belt and bed life. Use water only -no cleaners or abrasives. A mild soap and water solution along with a nylon scrub brush will clean the top of the textured belt. Allow to dry before using. Belt Dust -This occurs during normal break-in or until the belt stabilizes. Wiping excess off with a damp cloth will minimize buildup. General Cleaning -Dirt, dust, and pet hair can block air inlets and accumulate on the running belt. On a monthly basis, vacuum underneath your treadmill to prevent buildup. Once a year, you should remove the black motor hood and vacuum out dirt that may accumulate. UNPLUG POWER CORD BEFORE THIS TASK. BELT ADJUSTMENTS: If during use you notice that walking belt either shifts to the right or the left of center, first remove "Safety Key" and unplug equipment from AC power source. Using the M6 Allen wrench provided, turn right rear roller adjustment as indicated above clockwise no more the 1/4" of a turn. Remove the M6 Allen wrench, insert "Safety Key" and insert AC power cord into AC outlet. Turn on your treadmill and observe after running a few minutes to see if 18 Z8 problem has been corrected. This may take several adjustments, so repeat the above procedure. BELT / DECK LUBRICATION: Do not re-lube with other than Spirit lubricant. Spirit provides one application with this unit. See your Spirit dealer for additional purchases. The use of some other lubricants may destroy the deck surface or belt and will void warranty. Conditions exist beyond Spirit’s control on belt / deck cleanliness which relates to friction. You should apply the enclosed belt lubrication after approximately the first 50 hours of operation. Use all the contents of one container (no more) and spread lubricant onto middle portion (away from edges) of the deck (under treadbelt) along its width. When walked on, the belt will make certain an even coat is applied. Lubricant is not harmful to the skin. Lube will be distributed properly by walking at 2 to 3 mph for 3 to 5 minutes on all areas of the belt. Use handrails for support. The first few minutes you will be polishing your deck and lubricating the belt backing. Do not run on a newly lubricated belt until the above break-in procedure is done. If the treadmill belt/deck is kept reasonably clean it is possible to expect over 1000 hours before additional re-lubing is necessary. CAUTION -KEEP HANDS CLEAR OF MOVING REAR PULLEY! 19 Z8 Service Checklist -Diagnosis Guide Service Checklist -Diagnosis Guide Before contacting your dealer for aid, please review the following information. It may save you both time and expense. This list includes common problems that may not be covered under the treadmill’s warranty. PROBLEM SOLUTION/CAUSE Display does not light Tether cord not in position. Circuit breaker on front grill tripped. Push circuit breaker in until it locks. Plug is disconnected. Make sure plug is firmly pushed into AC household wall outlet. Household circuit breaker may be tripped. Treadmill defect. Contact your Spirit dealer. Treadbelt does not stay centered Treadmill belt hesitates when walked/run on A user may be walking while favoring or putting more weight on either the left or right foot. If this walking pattern is natural, track the belt slightly off-center to the side opposite from the belt movement. See General Maintenance section on Treadbelt Tension. Adjust as necessary. Motor is not responsive / Display is lit Make certain clock is running. Treadmill will only achieve approximately 7 mph but shows higher speed on display This indicates motor should be receiving power to operate. Low AC voltage to treadmill. Do not use an extension cord. If an extension cord is required it should be as short as possible and heavy duty 16 gauge minimum. Low household voltage. Contact an electrician or your Spirit dealer. A minimum of 110 volt AC current is required. Treadbelt stops quickly/suddenly when tether cord is pulled High belt/deck friction. See General Maintenance section on lubrication. Treadmill trips on board 15amp circuit High belt/deck friction. See General Maintenance Computer shuts off when console is touched (on a cold day)while walking/running Treadmill is not grounded. Static electricity is “crashing” the computer. Refer to Grounding Instructions on page 4. 20 Z8 Manufacturer’s Limited Warranty Manufacturer’s Limited Warranty Effective October 15, 2004 TREADMILL WARRANTY Spirit Manufacturing Inc. warrants all its treadmills’ parts for a period of 5 years from the date of retail sale, as determined by sale receipt, or eighteen (18) months from the original factory shipping date, whichever comes first. Spirit’s responsibilities include providing new or remanufactured parts, at Spirit...
Dieses Handbuch ist für folgende Modelle:Kraftstationen - Z500 (629.43 kb)
Kraftstationen - Z700 (629.43 kb)
Kraftstationen - Z300 (629.43 kb)