Stimmen - 6, Durchschnittliche Bewertung: 4 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 3.74 mb Dateiname: Unterrichtssprache:

• Check that the “TV Speakers” setting is On in the Audio/Video menu. 8. NetCommand unable to learn specific device keys. • Device does not use IR format for remote control signal. ITT and RF formats cannot be learned. • Room lighting may affect the signal. Have the remotes very close (6 inches or less) to the TV during Learning. • If using a Mitsubishi remote control make sure slide switch is not set to TV position. • Some but not all device key functions can be learned by NetCommand. For example, POWER and PLAY may be learned, but other functions may not. • The signal from the remote control may not be strong enough. Insert fresh batteries and try Learning again. 9. You have forgotten your V-Chip passcode. • See Appendix A, Bypassing the V-Chip Lock. 10. PIP does not display a picture. • Make sure the V-Chip lock is off. • Not all inputs can be displayed as a PIP. 11. Digital channels do not appear in PIP. • Only analog sources are available for PIP’s. 12. Not all channels appear in multiple PIP/POP. • Digital channels do not display in PIP/POP. 13. The sound does not match the screen picture. • NetCommand® is setup incorrectly. • The TV’s “Listen to:” setting may be set to SAP. • If using stereo or A/V receiver speakers, check their input selection. • If using stereo or A/V receiver, check that AUDIO 2 of MONITOR OUTPUT on TV’s back panel is connected to the A/V receiver and AUDIO 2 is the setting in NetCommand. 14. There is a large black or gray rectangle on the screen. • The TV’s analog closed captioning has been set to “text” mode in the Captions menu. Turn off because there is no text information being broadcast. 15. You cannot see a picture when playing a VHS tape. • Display the Device Selection menu and select the correct VCR. • Check your VCRs owner’s guide for further trouble shooting. 16. V-Chip is not working. • Make sure that V-Chip is On. • If V-Chip Hours are currently set to disable the V-Chip lock, the V-Chip will not block programming. 17. The TV will not turn on after being plugged in. • If green light on front panel is blinking, wait for at least one minute for the light to turn off, then press Power again. 18. TV functions do not respond to the remote control or to front panel control and will not Power Off. • Use the System Reset button as explained at the end of this section. 19. Name options not available for some channels • Only memorized analog channels can be named. 20. When viewing a stopped VCR, white lines are rolling on the screen. • Turn off video mute for the VCR. • Begin playing the tape. • Change the VCR input to the antenna input. 21. TV turned itself Off and the light on the Front Panel started to blink. • Momentary power fluctuation caused the TV to turn off to prevent damage. Wait for the green light to stop flashing and turn On again. • If the TV does not stay turned On, use the System Reset button. If this happens frequently, obtain an AC line power conditioner/surge protector. 22. When a Device is selected from the Device Selection menu, the screen is blue (no signal source). • Make sure the selected device is turned on. • From the Edit NetCommand® menu select Review setting. Verify that the inputs are actually connected to the TV . If they are not, either change the physical connections on the back panel, or select the Change setting on the Edit NetCommand menu to change the TV NetCommand’s settings for the connection. 23. The Device does not respond to button presses from the remote. • Remote has not been setup for NetCommand® use. • The incorrect manufacturer was selected during setup. Select the Change setting from the Setup menu and then the device to display the manufacturer selection. Change if necessary. • The device is not supported and keys have not been learned. • The requested function is not supported by NetCommand. Verify that the function is supported or keys are learned. • The IR emitter is incorrectly placed. Make sure the IR emitter is facing the IR sensor in the device. • The IR emitter is not plugged into the IR emitter Output NetCommand. • The IR emitter is facing the TV screen, causing double signals. Be sure that the IR emitter cannot send to the TV. 24. The A/V Receiver is the selected audio source but there is no sound. • Check to see if the A/V Receiver power is turned on. After the power is turned on, redisplay the Device Selection menu and press ENTER to allow NetCommand to correctly select the A/V Receiver input. • From the Setup Menu select Review setting. Check the Review screen to see if the A/V Receiver inputs and device correspond to the actual connections on the A/V Receiver. If they do not match, either change the actual connections, or select Change on the Edit NetCommand menu to change the device on the Connection screen. 25. The TV Speaker icon or A/V Receiver icon is grayed out and not selectable. • Select the Change setting from the Edit NetCommand menu, and then select the device (for example VCR). Once the Connection scree...

Herunterladen

Geben Sie zwei Ziffern: