. .Never use this tool in a manner that could cause a fastener to be directed toward anything other than the workpiece. . .Do not use the tool as a hammer. . .Always carry the tool by the handle. Never carry the tool by the air hose. . .Do not alter or modify this tool from the original design or function without approval from the manufacturer. . .Always be aware that misuse and improper handling of this tool can cause injury to yourself and others. . .Never clamp or tape the trigger or workpiec

Repair or replace damaged parts. 21. NEVER LEAVE UNATTENDED TOOL CONNECTED TO AIR. Disconnect the air hose and do not leave tool until it is relieved of any built up pressure. 22. NEVER ALLOW UNTRAINED USERS TO USE THIS TOOL WHILE UNSUPERVISED. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING TOOL. Seek formal training or research books or magazines that specialize in pneumatic tools. 24. BE AWARE OF HOSE LOCATION WHEN USING PNEUMATIC TOOLS. Hoses can easily become a tripping hazard w

1. Damaged seal. 1. Replace damaged seals. Tool skips nails 1. Excessive air pressure. 1. Reduce air pressure to while discharging. 2. Air leaks. 3. Dirt in nose. 4. Dirt or damage prevents nails from moving freely. 5. Inadequate air flow to tool. 6. Worn piston O-ring or lack of lubrication. 7. Damaged trigger valve O- rings. 8. Worn bumper. 9. Cap seal leaking. tool. 2. Reseal and tighten screws and fittings. 3. Clean nose. 4. Clean magazine and inspect/repair damage. 5. Check fittings, hose,

Figure 3. Loading nails into magazine. 4. Slide the nails all the way down to the nose of the nailer. 5. Release the magazine pusher by pulling back on the pusher and pressing in on the catch lever. Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer, do these steps: 1. Connect

Clean inspect the parts for cracks, wear, or burrs. 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with t

Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results. An in-line filter/lubricator/regulator unit, can be installed as depicted in Figure 1. This filter/lubricator/regulator unit will protect your tool from damaging water build-up, allow you to adjust and maintain regulated air pressure to your tool, and save you the inco

Vert. ° ° 58-40 90-65 57-32 70-44 50-28 59-31 Ruckdampfung dB 20-25 21-26 22-28 Spannbereich Mastschelle O mm 22-60 22-60 22-60 Lange mm 410 814 1345 Windlast bei 800 N/m2 N 40 59 106 Grenzwindlast bei 1100 N/m2 N 55 81 146 Verpackungs-Einheit/Gewicht St./kg 1/1,0 1/1,8 1/2,4 Ma.e der Einzelverpackung mm 490 x 420 x 75 825 x 500 x 75 840 x 500 x 95 Ubersicht der Kathrein-Maste Typ ZSD 48 ZSF 47 ZSF 48 ZSH 47 ZSH 48 ZSH 59 ZSH 62 2) Bestell.-Nr. 218380 218385 218381 218386 218394 218382 218383 La

B. Stroh, Reet oder ahnlichen Materialien. Betreten Sie nur stabile und trockene Dacher und sichern Sie sich gegen Herunterfallen. Leitern, Geruste, Sicherheitsgurte etc. mussen sicher sein. Passanten durfen durch evtl. herabfallende Teile nicht gefahrdet werden. Sichern Sie den Arbeits- bzw. Gefahrenbereich ab. Achten Sie darauf, dass die technischen Werte (z. B. die Windlast) Ihres Antennenstandrohres nicht uberschritten werden. Erkundigen Sie sich, falls Ihnen diese nicht bekannt sind, beim H

4) Ausrichten der Antenne Antenne durch Drehen auf besten Empfang ausrichten. Verwenden Sie hierfur gegebenenfalls ein Antennen- Messgerat. Wahlen Sie fur die Ausrichtung der Antenne ein beliebiges Programm am TV- oder Messgerat. Ziehen Sie nach der Ausrichtung die Flugelschrauben an der Mastschelle fest. .. Hinweis zum Empfang von DVB-T-Signalen Kathrein-Antennen sind werkseitig fur den Empfang von horizontal polarisierten Signalen vormontiert. DVB-T-Signale werden jedoch auch in vertikaler Pol

The air-o-steam combis are designed to form complete cook&chill systems together with the air-o-chill blast chillers/freezers, therefore, any installation can be tailored to meet the needs of the caterer. The air-o-steam combis detailed are 10 GN 2/1 electric Touchline models. OPERATING MODES • Selection window with three cooking modes (Automatic, Manual and Programs), cleaning cycles and setting mode. • Automatic mode: just select the family and food type and the oven will do the rest. Temperat