Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Clean inspect the parts for cracks, wear, or burrs. 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with the grooves on the guide. 11. After the piston is inserted correctly, close the magazine. Replace the rear cap assembly and tighten the four cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual for component locations. -11 Model W1776 2" Nailer Kit CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. Never clean this tool with gasoline or other flammable liquids. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death! Lubricating Standard pneumatic tool oil has been included with your new Shop Fox nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 7) before every use, or after 2 hours of continuous use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replace with a quality pneumatic tool oil. Another option to manual oiling would be to install a lubricator in your air compressor line. If your air compressor line already has a lubricator, then regular lubrication of your nailer will not be necessary. Just make sure there is always oil in the lubricator. Figure 7. Lubricating nailer via air inlet. -12 Model W1776 2" Nailer Kit W1776 PARTS BREAKDOWN ............................................................................................................................................................................................................................................................ .......................................................................................................... -13 Model W1776 2" Nailer Kit W1776 PARTS LIST REF PART..# DESCRIPTION REF PART..# DESCRIPTION 1 XPAW04M HEX..WRENCH..4MM 2 XPAW03M HEX..WRENCH..3MM 3 X1776003 CARRYING..CASE 4 X1776004 AIR..INLET..PLUG..1/4"..NPT 5 X1776005 END..CAP 6 X1776006 O-RING..40..X..2.65 7 X1776007 RUBBER..GRIP 8 XPSB41M CAP..SCREW..M4-.7..X..14 9 X1776009 LOCK..NUT..M4-.7 10 X1776010 GUIDE..BLOCK 11 X1776011 FIXED..MAGAZINE 12 X1776012 LATCH..BRACKET 13 XPSB18M CAP..SCREW..M4-.7..X..8 14 X1776014 LATCH..LEVER 15 XPRP42M ROLL..PIN..3..X..20 16 X1776016 COMPRESSION..SPRING 17 X1776017 MAGAZINE..BRACKET 18 XPSB56M CAP..SCREW..M3-.5..X..10 19 X1776019 PUSHER..SPRING 20 X1776020 PUSHER..SHAFT 21 X1776021 PUSHER 22 XPSS23M SET..SCREW..M4-.7..X..10 23 X1776023 MOVABLE..MAGAZINE 24 X1776024 CARBON..STRIP 25 XPSB57M CAP..SCREW..M3-.5..X..6 26 X1776026 GUIDE..BLOCK 27 XPSB16M CAP..SCREW..M4-.7..X..16 28 X1776028 GUIDE 29 X1776029 GUIDE..COVER..BRACKET 30 XPRP61M ROLL..PIN..3..X..12 31 X1776031 GUIDE..COVER 32 XPSB110M CAP..SCREW..M4-.7..X..6 33 X1776033 HANDLE 34 X1776034 HANDLE..COVER 35 X1776035 SLIP..BLOCK 36 X1776036 COMPRESSION..SPRING 37 X1776037 LOCK..PIN 38 X1776038 PIN..C4..X..12 39 X1776039 TORSION..SPRING 40 XPSB38M CAP..SCREW..M5-.8..X..25 41 X1776041 SEAL..COVER 42 XPRP64M ROLL..PIN..3..X..18 43 X1776043 SAFETY..SPACER 44 X1776044 TRIGGER 45 X1776045 COMPRESSION..SPRING 46 X1776046 O-RING..13.2..X..1.9 47 X1776047 TRIGGER..VALVE..SEAT 48 X1776048 O-RING..11.2..X..1.6 49 X1776049 SWITCH..SHAFT 50 X1776050 O-RING..1.9..X..1.1 51 X1776051 SCREW..SPRING 52 X1776052 VALVE..COVER 53 X1776053 O-RING..7..X..1.5 54 X1776054 SAFETY..BRACKET 55 X1776055 COMPRESSION..SPRING 56 X1776056 DEPTH..ADJUSTMENT..SCREW 57 X1776057 PIN..1.5..X..8 58 X1776058 SLIDING..BRACKET 59 X1776059 COMPRESSION..SPRING 60 XPRP55M ROLL..PIN..3..X..27 61 X1776061 BRACKET 62 X1776062 GUN..BODY 63 X1776063 SEALING..WASHER 64 X1776064 BUMPER 65 X1776065 CYLINDER. 66 X1776066 COLLAR 67 X1776067 O-RING..48.7..X..2.65 68 X1776068 MAIN..PISTON 69 X1776069 O-RING..23.5..X..2 70 X1776070 SEALING..WASHER 71 X1776071 GASKET 72 X1776072 SWITCH..VALVE 73 X1776073 O-RING..33.6..X..2 74 X1776074 COMPRESSION..SPRING 75 X1776075 O-RING..17..X..2.65 76 X1776076 SEALING..WASHER 77 X1776077 CYLINDER..COVER 78 XPLW01M LOCK..WASHER..5MM 79 XPSB15M CAP..SCREW..M5-.8..X..20 80 X1776080 EXHAUST..PORT 81 X1776081 COMPRESSION..SPRING 82 X1776082 SPECIAL..BOLT 83 X1776083 COMPRESSION..SPRING 84 X1776084 STEEL..BALL 85 X17...