Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results. An in-line filter/lubricator/regulator unit, can be installed as depicted in Figure 1. This filter/lubricator/regulator unit will protect your tool from damaging water build-up, allow you to adjust and maintain regulated air pressure to your tool, and save you the inconvenience of having to manually lubricate your tool every time you use it. If you plan on installing a filter/ lubricator/regulator unit in your compressed air system, always follow the connection instructions that come with the unit. Exceeding the maximum permissible operating pressure may damage the nailer and cause it to malfunction. To protect yourself from personal injury, DO NOT allow the air pressure to exceed the recommended pressure for this nailer! ................................................................................................................................................................................................................................ Figure 1. Typical filter/lubricator/regulator installation order. -5 Model W1774 18 Gauge Brad Nailer SETUP Unpacking This brad nailer has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1774. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully. Occasionally we pre-install certain components for safer shipping. ABCED Model W1774 Inventory Qty A. Brad Nailer............................... 1 B. Hex Wrench 3mm ....................... 1 C. Hex Wrench 4mm ....................... 1 D. Safety Glasses ........................... 1 E. Carrying Case............................ 1 -6 Model W1774 18 Gauge Brad Nailer Safety Nose Mechanism A safety mechanism on the nose of the nailer protects against accidental firing. When the trigger is pressed, the nailer will not fire until the safety nose mechanism is depressed. Before you use your nailer for the first time, check the safety nose mechanism to ensure proper function. To check the safety nose mechanism, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Make sure the magazine is empty and contains no nails. 3. Make sure the trigger and the safety nose mechanism move up and down without sticking. 4. Connect the nailer to the air supply. 5. Without pressing the trigger, depress the safety nose mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects. — If the nailer does not fire, then the safety nose mechanism is working correctly. — If the nailer does fire when you do this, immediately disconnect the nailer from the air supply and call Technical Support. — If the nailer fires when the trigger is pulled, without the safety nose mechanism being depressed, then the nailer is not working properly. — If you find that the safety nose mechanism is not working properly, check the lubrication of its sliding components. The safety mechanism is a mechanical device that can fail. Never rely on this mechanism as an excuse to point the nailer at yourself or any bystanders. Serious injury may occur. Operating this nailer can propel objects into the air, causing immediate eye damage. To protect yourself, always wear ANSI approved safety glasses or goggles when operating this equipment. DO NOT attempt to modify or bypass the safety nose mechanism to make the nailer/stapler fire without pushing the safety nose down. -7 Model W1774 18 Gauge Brad Nailer OPERATIONS Loading When replacing nails in your Model W1774, follow these guidelines: Gauge:........................................18 Length: .................................. 5.8"–2" Capacity: ................................... 100 To load your nailer, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Depress the magazine latch, as shown in Figure 2. Figure 2. Releasing magazine latch. 3. Pull the magazine cover back until it stops. 4. Insert a strip of nails, pointed-end down, into the magazine, as shown in Figure 3. Figure 3. Loading nails into magazine. 5. Slide the nails all the way down to the nose of the nailer. 6. Push the magazine cover forward until the magazine latch locks it in place. Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of quality pneumatic tool oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer, do these steps: 1. Connect the air supply to the quick connect fitting. 2. To test for proper nail penetr...