This will be removed later. 18 To Shape the Interior of a Bowl 1. Stop the lathe and move the tailstock away. Remove the center from the tailstock to prevent bumping it with your elbow. 2. Adjust the tool support in front of the bowl just below the centerline, at a right angle to the lathe bed. 3. Rotate the workpiece by hand to check the clearance. 4. Face off the top of the bowl by making a light shearing cut across the workpiece, from rim to center. 5. Place the 1/2" bowl gouge on the tool re

BD920N-CS09......... .........Rivet............................................... ..................2x5................ ...........2 10 ... 5020......................... .........Graduated Ring.............................. ...........1 11... ... BD920N-CS11......... .........Key................................................. ..................3x13.............. ............1 12... ...5023......................... .........Spring............................................. ............1

With features like a 25/32" spindle bore, a MT#3 tailstock and 6 spindle speeds you'll be able to turn some surprisingly hefty projects! If you're thinking of making parts for models, engines or even for repairs around the home or shop, this is the jettools.com JET 9" x 20" BELT DRivE BENcH LATHE 4 Way ■ Tool y Post j/ Enclosed Quick Change " Gear Box Adustable Tailstock d 4 L ■ ?- Ü.T Hardened and Ground Bedways Optional Stand 9" x 20" BELT DRivE BENcH LATHE • Spindle suppor

20) to desired rate. Note: for threading, lever (D) will be set at "C" or "E", depending on desired thread. 3. Push lever (B, Fig. 19) to the right. 4. Engage the half nut lever (C, Fig. 19). 5. To cut inch threads, reference the feed and thread tables. The half nut lever and the threading dial are used to thread in the conventional manner. The thread dial chart specifies at which point a thread can be entered using the threading dial. 6. To cut metric threads, the half nuts must be left continu

9 3. Apron -oil must be up to indicator mark in oil sight glass (A, Fig. 6). Top off with Mobil DTE. Oil Heavy Medium. Remove oil cap (B, Fig. 6) on top of apron to fill. To drain, remove drain plug on bottom of apron. Drain oil completely and refill after the first month of operation. Then, change oil in the apron annually. 4. Leadscrew Feed Rod -lubricate ball oiler (A, Fig. 7) on leadscrew/feed rod bracket with Mobil DTE. Oil Heavy Medium once daily. 5. Tailstock -lubricate two ball oilers (B

Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Lathe is assembled and running properly. Compare the contents of your container with the following parts list to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents of the Shipping Container 1 Lathe 1 Steady Rest (mounted on Lathe) 1 Fo

This new 10HP ZX Series lathe boasts a 22" swing over bed and comes standard with a 10" 3-jaw chuck with top reversing jaws and a 12" 4-jaw chuck. The 22" ZX Series Large Spindle Bore Lathe comes equipped with a 3-1/8" bore spindle supported by two tapered bearings and one ball bearing and a universal gear box with pitch threads in inches, metric, diametral and module. The universal gear box is dial controlled eliminating the need for changing end gears. The GH-2280ZX also comes standard with a

However, it is a good practice to thoroughly check the machine for loose fasteners, handles, etc. before use. Controls Tailstock Handwheel (A, Fig. 1) - turn clockwise to move tailstock spindle forward. Turn counter-clockwise to retract tailstock spindle. Tailstock Spindle Lock (B, Fig. 1) - locks tailstock spindle. Release to adjust with handwheel. Tailstock Lock (C, Fig. 1) - locks tailstock in position on the bed. Release to move tailstock assembly closer to or farther from the headstock.

M-708376 Ph.: 800-274-6848 Revision A 9/06 Copyright © WMH Tool Group WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. Fo

This ^ HP lathe supports stock up to 10" in diameter and 14" in length. This lathe features solid cast iron construction, the added convenience of a hollow tailstock, a 6" tool rest and electronic variable speed. The spindle also has a versatile locking/indexing mechanism for fluting and veining applications. rri JET 10"x14" VARIABLE SPEED INDEXING MINI LATHE 10"x14" VARIABLE SPEED INDEXING MINI LATHE • continously variable speed operation from 500-3900 rpm • Heavy-duty cast-iron lathe bed