Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
9 3. Apron -oil must be up to indicator mark in oil sight glass (A, Fig. 6). Top off with Mobil DTE. Oil Heavy Medium. Remove oil cap (B, Fig. 6) on top of apron to fill. To drain, remove drain plug on bottom of apron. Drain oil completely and refill after the first month of operation. Then, change oil in the apron annually. 4. Leadscrew Feed Rod -lubricate ball oiler (A, Fig. 7) on leadscrew/feed rod bracket with Mobil DTE. Oil Heavy Medium once daily. 5. Tailstock -lubricate two ball oilers (B, Fig. 7) on tailstock with Mobil DTE. Oil Heavy Medium once daily. 6. Cross Slide -lubricate four ball oilers (A, Fig. 8) with Mobil DTE. Oil Heavy Medium once daily. 7. Compound Rest -lubricate one ball oiler (B, Fig. 8) with Mobil DTE. Oil Heavy Medium once daily. 8. Carriage -lubricate four ball oilers (D, Fig. 8) with Mobil DTE. Oil Heavy Medium once daily. 10 Coolant Preparation . CAUTION Follow coolant manufacturer's recommendations for use, care, and disposal. 1. Remove rear access cover on tailstock end. Make sure coolant tank has not shifted during transport and is located properly under the recovery chute (Fig. 9). 2. Pour three gallons of coolant mix into drip pan. 3. After machine has been connected to power, turn on coolant pump and check to see coolant is cycling properly. 4. Fasten coolant door to stand. Electrical Connections . WARNING All electrical connections must be completed by a qualified electrician! Failure to comply may cause serious injury and / or damage to the machinery and property! The GH-1340W-1 & GH-1440W-1 Gear Head Lathes are rated at 3HP, 1Ph, 230V only. Confirm power available at the lathe's location is the same rating as the lathe. The GH-1340W-3 & GH-1440W-3 Gear Head Lathes are rated at 3HP, 3Ph, 230V/460V prewired 230V. Confirm power available at the lathe's location is the same rating as the lathe. Lathe Power Source Junction Box: Remove the cover. Run the main power through the strain relief bushing and attach the ground, followed by power leads. Replace the cover. Main Power Switch: Located on the backside of the machine. Turns the power to the machine on and off. 11 Make sure the lathe is properly grounded. Power is connected properly when pulling up on the forward-reverse lever causes the spindle to rotate counter-clockwise as viewed from the tailstock. If the chuck rotates in the clockwise direction, disconnect the lathe from the power source, switch two of three power leads (for GH-1340W-3 & GH1440W-3), and connect the lathe to the power source. To Switch from 230V to 460V Operation GH-1340W-3 & GH1440W-3 Only . WARNING Disconnect the machine from the power source! Failure to do so may cause serious injury! Main Motor: Change the wires according to the diagram on the inside of the motor junction box. Transformer: Remove electrial panel on rear of the machine, headstock side, switch wire from 230V terminal to 460V terminal as outlined on the transformer. Coolant Pump: Open access panel on the base at the tailstock end. Change wires in coolant pump junction box according to diagram on the inside of the junction box cover. General Description Lathe Bed The lathe bed (A, Fig. 10) is made of high grade cast iron. By combining high cheeks with strong cross ribs, a bed with low vibration and high rigidity is realized. Two precision ground vee slideways, reinforced by heat hardening and grinding, are an accurate guide for the carriage and headstock. The main drive motor is mounted in the stand below headstock. Headstock The headstock (B, Fig. 10) is cast from high grade, low vibration cast iron. It is bolted to the bed by four screws with two adjusting screws for alignment. In the head, the spindle is mounted on two precision taper roller bearings. The hollow spindle has Morse Taper #5 with a 1-1/2" bore. Carriage The carriage (A, Fig. 11) is made from high quality cast iron. The sliding parts are smooth ground. The cross slide is mounted on the carriage and moves onadovetailedslide which can be adjusted for play by means of the gibs. The compound slide (B, Fig. 11), which is mounted on the cross slide (C, Fig. 11), can be rotated through 360°. The top slide and the cross slide travel in a dovetail slide and have adjustable gibs. A four way tool post is fitted on the top slide. Four Way Tool Post The four way toolpost (D, Fig. 11) is mounted on the top slide and allows a maximum of four tools to be mounted simultaneously. Remember to use a minimum of two clamping screws when installing a cutting tool. Apron The apron (E, Fig. 11) is mounted to the carriage. In the apron a half nut is fitted. The half nut gibs can be adjusted from the outside. The half nut is engaged by use of a lever. Quick travel of the apron is accomplished by means of a bed mounted rack and pinion, operated by a hand wheel on the front of the apron. 13 Tailstock The tailstock (A, Fig. 12) slides on a v-way and can be locked at any location by a clamping lever. The tailstock has a heavy duty spindle with a Mo...
Dieses Handbuch ist für folgende Modelle:Drehmaschinen - GH-1340W (1.92 mb)