This Warranty does not extend to the elimination of externally generated static or noise, to costs incurred for installation, removal or reinstallation of the product, damage to speakers, accessories, or vehicle and home electrical systems, malfunction of satellite transmissions, repeater signal or receiver unit. This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, mi

RIGHT - LEFT - LEFT+ GREENWHITEGRAYBROWNBLACK CHASSIS GROUND ONRADIO -6 128-5721 128-5721128-5721128-5721128-5721128-5721SHT. 8 OF 12 SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12 WARNING! l THIS AMPLIFIER IS DESIGNED FOR USE WITH 2 SPEAKERS l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER. l NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER. OUTPUT WIRING DIAGRAM OR GREASE FROM OR GREASE FROMOR GREASE FROMO

Tighten the screw down to secure the wire. 1. Power Connection The battery terminal (+12V) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block) will reduce the power output and may cause noise and distortion. Use only #16 gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal of the battery after all other w

Ground Connection2. Ground Connection2. Ground Connection The ground terminal (GND) connection is also critical to the correct operation of the amplifier. Use a wire of the same gauge as the power connection (#12 #12#12#12#12#12 or thicker) and connect it between the ground terminal (GND) of the amplifier and a metal part of the vehicle close to the mounting location. This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide a clean m

We therefore advise that you read these instructions very carefully to familiarize yourself with the product and it's features. Should you require assistance with the installation or wiring of this unit, please call our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown. SPECIFICATIONS Maximum Output Power 4-Channel Operation: 125 watts x 4 2-Channel Operation: 500 watts x 2 Output Power @ 1% T.H.D. 4-Channel Operation: 600 watts RMS x 4 2-Channel Operation: 120 watts RMS x 2 Ou

Carefully splice and insulate all wire connections. CAUTION: CAUTION:CAUTION:CAUTION:CAUTION:CAUTION: Use either the low-level or the high-level inputs on the amplifier. DO NOT DO NOTDO NOTDO NOTDO NOTDO NOT use both input levels at the same time. -5 USE THIS INPUT WIRING WITH STEREO AND MIXED-MONO INPUT WIRING DIAGRAM OUTPUT WIRING ON PAGE 7 LOW-LEVEL HIGH-LEVEL CAR STEREO (SPEAKER) OUTPUTS RCA OUTPUTS LEFT RIGHT RIGHT + LEFT LEFT + RIGHT IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT

Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustration. 3. Remove the amplifier and drill a 1/8" hole at each of the four locations. CAUTION: CAUTION:CAUTION:CAUTION:CAUTION:CAUTION: Before drilling the holes, look at the underside of the mounting surface. Always check carefully to avoid drilling into wiring, braces, fuel or brake lines. CHECK BEFORE YOU CHECK BEFORE YOUCHECK BEFORE YOUCHECK BEFORE YOUCHECK BEFORE YOUCHECK BEFOR

This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground wire can be screwed or bolted. 3. Remote Turn-On Connection The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car stereo is turned on. If the car

INSTALLATION INSTRUCTIONS MOUNTING SURFACE DRILL 1/8" HOLE SELF-TAPPING SCREW WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a 4-Channel, 3-channel, 2-channel, or mixed-mono application. The following pages illustrate the input and output wiring for these types. Please refer to the appropriate diagrams for the system configuration you are using. The power and speaker wire connections for this amplifier are made via screw t