Like other members of the 985 family, 985DTV modules can be cascaded to allow virtually an unlimited number of television monitors to be driven from a single source without picture degradation. The exceptional bandwidth of this product supports video standards from today on into the future. The 985DTV can also be used for RGB video distribution in video production and duplication facilities. Digital audio distribution complements the 985DTV's video capability by providing lossless transmission

The GROUP address should be higher than the highest speaker GROUP address. The mono subwoofer bus cable connects to the stereo jacks with a “Y” adapter. Instructions for other types of subwoofer configurations are available if needed. Contact our Sales department at the phone number below. Write in switch settings in each boxs Setting for Bypass Group Number Setting System Bus Connections Model 922 Stereo Low-Level Selector Do Not Use these ports in Home-Audio Applications “Y” Cable for b

To demonstrate receivers with more than two channels, see the drawing for Dolby Digital and ProLogic Receivers. Instructions for other types of two-channel receiver or amplifier configurations are available if needed. Contact your Account Manager at the phone number below. System Bus Connections Do Not Use these ports in Home-Audio Applications All switches OFF (Used in car audio only) Group Number Setting Module ID Settings Stereo Audio Low Level Input Bus Connections (Input from source)

Black) 916X DC Power Adapter JTON! BEFORE SERVICING. 916X T01 ©2 ©3^)4^ System Bus Connections Settings for Bypass & Amp Turn On Delay Address Settings Low Level Bus Connections < (IN & OUT) ^ High-Level Bus Connections ■ Audio Signal Expansion Port Amp Bypass Note: This amp could not be connected in position #4 as shown if this were the last module in an Amplifier Product Group to be bypassed. Audio^^Authority* Tech Support USA and Canada: 800-322-8346 (Mon-Fri 8:30 AM to 5:00 PM E

See Appendix A for other system related connections such as System Bus, DC distribution, or Low-Level and High-Level Bus. Amp (position. #4) DC Connections Switched + (Blue) Battery (Yellow) Ground (Black) 916X DC Power Adapter JTON! BEFORE SERVICING. 916X T01 ©2 ©3^)4^ System Bus Connections Settings for Bypass & Amp Turn On Delay Address Settings Low Level Bus Connections < (IN & OUT) ^ High-Level Bus Connections ■ Audio Signal Expansion Port Amp Bypass Note: This amp could not b

be connected in position #4 as shown if this were the last module in an Amplifier Product Group to be bypassed. Audio^^Authority* Tech Support USA and Canada: 800-322-8346 (Mon-Fri 8:30 AM to 5:00 PM Eastern Time) 48 Phone: 859-233-4599 Fax: 859-233-4510 Hookup drawings and FAQ http://www.audioauthority.com

In multi-room applications, several receiver/speaker packages may be desirable. (use either singlal path) Digital Receiver and Speakers I Component Video Left/Right Audio LJo 985U, oo OJÈ? > o o o o o o oo oo o o o o o o o o o o oo oo o o o o o o LJo 985U oo oo o o o o o o oo oo o o o o o o o o o o oo oo o o o o o o 120V AC Power Supply 985U oo o c o o o °c° °< o oo o oo °o°°( o oo Left/Right Audio Sample Component (Y Pb Pr) Video and Digital Audio Distribution Sy

It makes no difference if selection of product is by Control Panel or by Product Select Buttons or both, therefore, always follow this diagram for proper setup. Concerning signal path, the Model 980EZ will be located just before the amplifier inputs (see Appendix A). In the 2-channel configuration, the Front Inputs and Front Outputs are the only connections that are used. In the 6-channel configuration, all three sets of inputs/outputs are used. The Low-Level buses (e.g., front, rear, sub) conti

If a receiver does not have some of the features shown, simply leave those jacks or terminals vacant on the 947. Always connect the A/V cables to the VCR 1 or Video 1 jacks on the receiver. To prevent a blank screen when switching from a GUI reciver to a non-GUI receiver, you should install a 986 Video AutoPatcher in your system. There is no optical digital connection on the 947 - use the coax input on digital audio receivers, or use Model 977T Coax to Optical Adapter. Instructions for other typ

Unlike passive balun systems, the UniDrive employs Active Gain Equalization (AGE), dramatically extending range and signal integrity. In addition to HDTV audio and video signals, the UniDrive has a 3-conductor pathway for infrared control signals. This pathway can be used for signals traveling in either direction. The system includes one Model 9880T Cat 5 Transmitter, and one Model 9880 Cat 5 Receiver. The cable length compensation adjustment on the receiver allows the installer to fine tune im