We reserve the right to make modifications. All rights, including those regarding the translation, are reserved. Approval The transfer printers comply with the following safety guidelines: CE EC Low-Voltage Directive (73/23/EEC) EC Machine Directive (98/37/EC) EC Electromagnetic Compatibility Directive (89/336/EEC) FCC Conditions from Part 15 of the FCC Regulations for Class A computing devices. Operation of this device may cause radio or television interference under unfavorable conditions, whi

While every precaution has been taken in preparation of this document, Brady assumes no liability to any party for any loss or damage caused by errors or omissions or by statements resulting from negligence, accident, or any other cause. Brady further assumes no liability arising out of the application or use of any product or system described, herein; nor any liability for incidental or consequential damages arising from the use of this document. Brady disclaims all warranties of merchantabilit

See page 16. Calibrate the printer (see page 17). Brady X-PLUS Series User.s Guide Error Condition Head Open Problem Solution The printhead is not fully closed. Close the printhead. Error Condition Head Element Bad Problem Solution One or more of the printhead elements have failed the printhead element test. If the failed elements impact your printing application, replace the printhead. To override this error, disable the head test count feature on the front panel by defaulting the value to .000

2) Close the printhead. CALIBRATING PLEASE WAIT The printer automatically adjusts the scale (gain) of the signals it receives from the media and ribbon sensors based on the specific media and ribbon combination you are using. On the sensor profile, this essentially corresponds to moving the graph up or down to optimize the readings for your application. ---RELOAD ALL When .RELOAD ALL” is displayed: 1) Open the printhead and pull the media forward until a label is positioned under the media senso

Check the display screen for more information. CHECK RIBBON Off Normal operation — ribbon (if used) is properly loaded. On Printing is paused, the front panel displays a warning message, and the PAUSE light is on. • If the printer is in direct thermal mode: Ribbon is loaded. • If the printer is in thermal transfer mode: No ribbon is loaded. PAPER OUT Off Normal operation — media is properly loaded. On No media is under the media sensor. Printing is paused, the display shows an error message, and

±0.039" (±1.0mm) on noncontinuous media Horizontal . ±0.039" (±1.0mm) within a roll of media • Programmable print speeds: - 203 dpi models = 2.0" (51mm) through 10" (254mm) per second in 1" increments - 300 dpi model = 2.0" (51mm) through 6" (152mm) per second in 1" increments MVP Series Product Guide Page 18 Printer Specifications Media Specifications • Maximum label length: 39" (991mm) • Media type: continuous, die-cut, tags, black- mark • Media web width (label and liner): 1.0" (25.4mm) to 4.

(Fo. Serial-Interfac. Printer. Only. The M-Series Printer, with the RS-232 Serial Interface, uses eight miniature switches located on the rear of the printer, above the Signal Interface Cable Connector. The ON/OFF positions of these switches establish some of the Printer Configuration Parameters. Bank 1 switches must be properly positioned to establish serial data communications with the host computer. Thereafter, the position of these switches should not be changed. Note: Parallel-interface pri

Default: Web Selections: Web, mark This parameter tells the printer whether you are using media with a web (gap/space between labels, notch, or hole) to indicate the separations between labels or if you are using media with a black mark printed on the back. If your media does not have black marks on the back, leave your printer at the default (web). PRINT METHOD Selecting Print Method Press the RIGHT BLACK OVAL key for the next value; press the LEFT BLACK OVAL key for the previous value. Default

At power up or in an idle condition, this value should be in the range of 060 to 065. A reading of 175 is high and could decrease the life of the printhead. An average amount of printing will give readings that range from 070 to 120. Pot -this reading comes from the darkness potentiometer located on the front panel board. It will vary from 000 (darkest) to 255 (lightest). Adjust this value for a midrange value of 128. TOFA -(Top of Form Adjustment) determines where the first position of print be

These characters are available in fonts 1–6 and 9. Getting Started 13 _______________________________________________________________________ 14 Getting Started 2.4 Memory Cartridges The Printer has one standard memory cartridge slot. The primary use of the memory cartridges is for storing label formats, graphic images, fonts and for internal batch. Follow the instructions outlined below when installing memory cartridges. 1. Ensure that all printing has been completed. 2. Open the Side Access Co