Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Brady Dateigröße: 1.26 mb Dateiname: 49320959-b1d2-47b0-ae1e-157b4333f55d.pdf Unterrichtssprache:

Default: Web Selections: Web, mark This parameter tells the printer whether you are using media with a web (gap/space between labels, notch, or hole) to indicate the separations between labels or if you are using media with a black mark printed on the back. If your media does not have black marks on the back, leave your printer at the default (web). PRINT METHOD Selecting Print Method Press the RIGHT BLACK OVAL key for the next value; press the LEFT BLACK OVAL key for the previous value. Default: Thermal transfer Selections: Thermal transfer, direct thermal The print method parameter tells the printer the method of printing you wish to use: direct thermal (no ribbon) or thermal transfer (using thermal transfer media and ribbon). NOTE: Selecting direct thermal when using thermal transfer media and ribbon creates a warning condition, but printing will continue. Brady X-PLUS Series User.s Guide Press Display Shows Action/Explanation PRINT WIDTH Setting Print Width Press the RIGHT BLACK OVAL key to increase the value, press the LEFT BLACK OVAL key to decrease the value. To change the unit of measurement, press the LEFT BLACK OVAL key until the unit of measurement is active, then press the RIGHT BLACK OVAL key to toggle to a different unit of measure (inches, mm, or dots). Default:, Range: The default and range of acceptable values vary depending on what printer you have. Refer to .Printing Specifications” on page 90 for further information about the ranges available for your model. Print width determines the printable area across the width of the label. MAXIMUM LENGTH Setting Maximum Length Press the LEFT BLACK OVAL key to decrease the value, press the RIGHT BLACK OVAL key to increase the value. Default:, Range: The default and range of acceptable values vary depending on your printer.s configuration. Values are adjustable in 1” (25.4 mm) increments. Maximum length is used in conjunction with the calibration procedure. The value of this setting determines the maximum label length that will be used during the media portion of the calibration process. Only a few labels are required to set media sensors. Always set the value that is closest to, but not lower than, the length of the label you are using. For example, if the length of the label is 14.5 inches (368 mm), set the parameter for 15.0 inches (381 mm). Brady X-PLUS Series User.s Guide Listing Printer Information Press Display Shows Action/Explanation LIST FONTS List Fonts Press the RIGHT BLACK OVAL key to print a label listing all of the available fonts. This selection is used to print a label that lists all of the fonts currently available in the printer, including standard printer fonts plus any optional fonts. Fonts may be stored in RAM, FLASH memory, font EPROMs, or font cards. LIST BAR CODES List Bar Codes Press the RIGHT BLACK OVAL key to print a label listing all of the available bar codes. This selection is used to print a label that lists all of the bar codes currently available in the printer. LIST IMAGES List Images Press the RIGHT BLACK OVAL key to print a label listing all of the available images. This selection is used to print a label that lists all of the images currently stored in the printer.s RAM, FLASH memory, optional EPROM, or optional memory card. LIST FORMATS List Formats Press the RIGHT BLACK OVAL key to print a label listing all of the available formats. This selection is used to print a label that lists all of the formats currently stored in the printer.s RAM, FLASH memory, optional EPROM, or optional memory card. LIST SETUP List Setup Press the RIGHT BLACK OVAL key to print a label listing the current printer configuration. This selection is used to print a label that lists the current printer configuration information. (Same as CANCEL key self test.) LIST ALL List All Press the RIGHT BLACK OVAL key to print a label listing all of the available fonts, bar codes, images, formats, and the current printer configuration. This selection is used to print a label that lists the five previous selections, as described. Brady X-PLUS Series User.s Guide Press Display Shows Action/Explanation INITIALIZE CARD Initialize Memory Card CAUTION: Perform this operation only when it is necessary to erase all previously stored information from the optional memory card. Press the NEXT//SAVE key to bypass this function. 1. Press the RIGHT BLACK OVAL key to select .YES.” If your printer is set to require a password, you will now be prompted to enter the password. Enter the password and then press the NEXT/SAVE key. 2. The display will ask .INITIALIZE CARD?.. Press the RIGHT BLACK OVAL key .YES.” 3. The front panel LCD will ask .ARE YOU SURE?.. 4. Press the RIGHT BLACK OVAL key .YES” to begin initialization. or Press the LEFT BLACK OVAL key .NO” to cancel the request and return to the .INITIALIZE CARD” prompt. 5. Press the SETUP/EXIT key followed by the NEXT/SAVE key. If initialization is still in process, the front panel display will flash back and fort...

Herunterladen

Geben Sie zwei Ziffern: