Therefore, when calculating the value of each column of graphics the value of bit 7 (which is 64) must be added to the value of the print wires. The resulting value for column 1 is then 127 (63 plus the value of bit 7). 4-45 Column 2 contains no dots and therefore column 2 has a value of 64 (0 plus bit 7). This is also true for columns 3,4 and 5. In column 6 all six print wires are fired so column 6 has a value of 127 (63 plus bit 7). Columns 7,8,9,10 and 11 also have a value of 127. In column

Input Capacity: a) Standard 250 sheets tray x 1 100 sheets multi bypass tray* *Bypass tray and duplex unit do not work together. b) Options Paper Bank: 500 sheets x 1 Max total capacity: 850 sheets 5. Output Capacity: 250 sheets (internal tray) 6. Paper size / weight: a) Size: Standard Tray: A5 (LEF), A4 (SEF), 5 1/2” x 8 1/2” (LEF), 8 1/2” x 11”(SEF) Bypass Tray: A6 (SEF) – A4 (SEF), 5 1/2”x 8 1/2” - 8 1/2”x 14”(SEF) Irregular size: 90 - 216 x 139 - 600 mm 3.54” - 8.5” x 5.48” – 23.62” Duplex:

NOTE To eject a cut sheet form for any reason, press the Form Feed Key. Figure 3-7: Tear Off Bar Scale 3-10 Forms Handling User’s Guide NOTE If forms length is between 4.5” and 6.0”, verify that the Vertical Gap Position Feature is set to 0.0” (located under M8 Form Thickness in the setup mode). See Section 4.6 for further instructions on how to change this setting. Failure to set Vertical Gap for these forms may cause trailing edge of form to catch under guide during loading. Figure 3-8: Loadin

108738 Rev. C NOTICE There are no user-servicable parts inside the side access panel on theCodewriter 4500 Series products. Do not attempt to open the sideaccess panel without first turning off the power to the unit, disconnecting the power cord from the unit, and disconnecting allcommunication cables. All service procedures should be performed by a qualified servicetechnician. NOTICE This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. Thi

The value of 4 lines per inch .......... ESC A SI 1B 41 0F 27 б5 15 variable n defines the line spacing distance: 6 lines per inch .......... ESC A LF 1B 41 0A 27 б5 10 8 lines per inch .......... ESC A BS 1B 41 08 27 б5 8 Line spacing = n x 1/72-inch (Epson JX & IBM XL24) 12 lines per inch........ ESC A ENQ 1B 41 05 27 б5 5 Line spacing = n x 1/60-inch (Epson LQ-2550) Note: When the IBM XL24 emulation is active, the Set Vertical Units sequence forces the vertical spacing unit to either 1/7

387002, Rev. E ® ™ AMT ACCEL-6300 P R I N T E R S E R I E S User's Guide Unpacking Set Up Loading Paper Control Panel Cleaning & Maintenance Solving Problems Bottom-Feed Tractors Bar Codes Interfaces Code Sets Specifications Document No. 387002 .. Revision E AMT Datasouth Corp. 4765 Calle Quetzal Camarillo, CA 93012 TEL: (805) 388-5799 FAX: (805) 484-5282 WEB: amtdatasouth.com User's Guideii Preface User's Guide Preface Thank you for selecting an AMT Datasouth® ACCEL™-6300 series printer. Using

D Contents... Table of Introduction.............................................................. i 1. Before Using the ATB Printer.........................1-1 1.1 Checking the Package ....................................................... 1-2 1.2 Names and Functions ........................................................ 1-3 2. Operation..........................................................2-1 2.1 Connecting the ATB Printer..............................................2-2 2.2 Turning the

110621 A IMPORTANT SAFETY INSTRUCTIONS AND OTHER NOTICES • This label printer complies with the requirements in Part 15 of FCC rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interface to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference. • Place the printer on a flat, firm and solid surface. • Do not place the printer near a heat source or near water. • Refer to the speci

0.1 0.1 3.9 1.9 0.01 Box would also work. % Box draw % botX(in.) botY(in.) topX(in.) topY(in.) lwidth(in.) Box 0.1 0.1 3.9 1.9 0.01 Box Fastmark 600 Series User's Guide Demo Label showing use of Print Utility Procedures After the file Pal_Procs_and_Formats.txt has been copied to the printer, a number of new procedures are now defined in the printer (until powered off). These procedures have been written specifically to demonstrate how to use the PALTM Print and Program operators to produce print

It provides added versatility by combining a super-impact printhead with a powerful bottom-feed forms tractor to conquer even the most impossible jobs! The Paper Handling Expert • Straight-thru paper path • Single/dual tractor models plus cut sheet • Cut form sets up to 33" long • Snap-in printer cartridge and color printing The Form Pounder • 12-part forms with carbons capability • Tough 24-pin printhead, 480 cps print speed • Demand document Ready for Any Application • 5 standard em