Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
always make sure the float/water sensor isin the dirt tank and not outside of the tank. caUtIon: Do not run any objects including cars over hose. WaRnInG: Do not suck up volatileor flammable liquids such as gasoline, kerosene or oil. 800.237.7691 7 ug110-4053_18P0_608.indd 7 6/13/08 12:35:30 PM Operation thermal motor protection: an internal thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates, the main vacuum motor will stop operating. If this happens, proceed as follows. 1. Turn the vacuum OFF and unplug from electrical outlet. 2. Check the vacuum for the source of overheating problem (i.e. full dirt tank, dirty filters or clog). 3. Fix the problem by following the steps in the maintenance section of the user guide. Face plate Green lED light the lED power will turn on when unit is turned on. yellow lED light the lED full dirt tank indicator will turn on when dirt tank needs emptying. Red lED light the lED full water tank indicator will turn on when water level is too high. Using the tools Make sure the tools are secure to the hose or wand before using. 1. Attach extension wand to end of hose by pushing it firmly onto the hose. 2. Attach additional wand or tool, if desired, by firmly inserting onto the wand. 3. Use the hose and wand alone or attach any of the tools to the end of the hose wand. Accessories 32 ft flexible crush proof hose Hose holder accessory caddy Mounting bracket 800.237.7691 8 ug110-4053_18P0_608.indd 8 6/13/08 12:35:31 PM Floor cleaning (2) Extension wands Use with desired attachment for a longer reach. large area cleaning tool OperationFloor cleaning (2) Extension wands Use with desired attachment for a longer reach. large area cleaning tool Operation Use on large surfaces for maximum pick up. Multi surface floor tool May be used on both carpet/rugs or hard floor surfaces. for use on carpets, make sure the tab is in the down position . this will hide the soft outer brushes. for hard floor surfaces, press the opposite tab in the down position . this will engage the soft outer brushes. Upholstery cleaning crevice tool May be used for both dry vacuuming or wet cleaning in tight spaces and corners. Dusting brush Use soft bristles for dusting vehicle interior. Small upholstery tool 5” tool may be used for small, quick pick ups. Car detailing Precision suction tool 3” tool may be used for cleaning your vehicle. Precision blower tool May be used to blow air to get rid of unwanted debris in tight spaces. (3) Small, medium and large detailing tools May be used to clean small crevices and edges in your vehicle. Emptying the dirt tank Empty the dirt tank after every use. If red light indicates, empty dirt tank. 1. Unplug the unit from the electrical outlet. Unclip the dirt tank handles while holding the bottom portion of the vacuum. Empty over trash can. 2. Reattach the dirt tank to the main unit by aligning the top of the dirt tank to the upper portion of the vacuum. Use one hand to hold the tank and use the other hand to clip the handles to hold the tank securely. Carpet Hard Floor 800.237.7691 9 ug110-4053_18P0_608.indd 9 6/13/08 12:35:32 PM Maintenance and care Cleaning the dirt tank 1. Unplug the unit from electrical outlet. 2. Remove the dirt tank by pulling up on both handles to unlatch. 3. Ensure the dirt tank has been emptied. 4. The dirt tank may be washed in warm water. Make sure it is completely dry before reassembling. 5. Reattach the dirt tank to the main unit by aligning the top of the dirt tank to the upper portion of the vacuum. Use one hand to hold the tank and use the other hand to clip the handles to hold the tank securely. Cleaning the filters the filter should be checked every 15-30 days and washed as needed to maintain performance. frequency of cleaning will be based on individual use. Primary filter 1. Unplug the unit from electrical outlet. 2. Remove the dirt tank by pulling up on both handles to unlatch. 3. The filter is located inside the top portion of the vacuum. Pull either black tab towards the middle of the unit and remove. 4. Shake filter over trash can to release any loose debris. 5. Use a damp cloth to wipe the inside and outside of the filter if desired. Air dry thoroughly before replacing. 6. To replace, hold one edge of the filter, collapse and snap in. 7. Reattach the dirt tank to the main unit by aligning the top of the dirt tank to the upper portion of the vacuum. Use one hand to hold the tank and use the other hand to clip the handles to hold the tank securely. 10 800.237.7691 ug110-4053_18P0_608.indd 10 6/13/08 12:35:32 PM Maintenance and careCleaning the filters continued Secondary filter 1. Cleaning the filters continued Secondary filter 1. The secondary filter is located above the primary filter. 2. To remove the primary filter, see instructions on page 10. 3. To remove the secondary filter, pull filter down and out. 4...
Dieses Handbuch ist für folgende Modelle:PC Notebooks - GARAGE PRO 18P0 (526.32 kb)