Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Bissell Dateigröße: 526.32 kb Dateiname: Unterrichtssprache:

frequency of cleaning will be based on individual use. Primary filter 1. Unplug the unit from electrical outlet. 2. Remove the dirt tank by pulling up on both handles to unlatch. 3. The filter is located inside the top portion of the vacuum. Pull either black tab towards the middle of the unit and remove. 4. Shake filter over trash can to release any loose debris. 5. Use a damp cloth to wipe the inside and outside of the filter if desired. Air dry thoroughly before replacing. 6. To replace, hold one edge of the filter, collapse and snap in. 7. Reattach the dirt tank to the main unit by aligning the top of the dirt tank to the upper portion of the vacuum. Use one hand to hold the tank and use the other hand to clip the handles to hold the tank securely. 10 800.237.7691 ug110-4053_18P0_608.indd 10 6/13/08 12:35:32 PM Maintenance and careCleaning the filters continued Secondary filter 1. Cleaning the filters continued Secondary filter 1. The secondary filter is located above the primary filter. 2. To remove the primary filter, see instructions on page 10. 3. To remove the secondary filter, pull filter down and out. 4. Shake filter over trash can to release any loose debris. 5. Rinse filter with warm water. 6. To replace filter, insert into top portion of vacuum. Clearing clogs low suction or poor pickup may be due to a clog in the vacuum. If this occurs, the lED full dirt tank indicator light will turn yellow and indicate airflow is restricted. If there is no suction or if suction is reduced at the hose, follow these steps to clear the clog: 1. Unplug vacuum from electrical outlet. 2. Check the filter and clean as necessary (see cleaning your filters above and on page 10). 3. Check to see if dirt tank is full. Empty if needed. 4. Check wet/dry or blower outlet for clogs. If the clog is contained near the top of the hose (close to the unit), follow these steps: 1. Attach hose to the wet/dry inlet and turn the power on. 2. This should dislodge the clog by sucking in debris. 11 800.237.7691 ug110-4053_18P0_608.indd 11 6/13/08 12:35:32 PM Maintenance and care Clearing clogs continued If the clog is contained near the bottom of the hose (close to where tools are attached), follow these steps: 1. Remove wand or tool. 2. Attach hose to the blower outlet and turn the power on. 3. This should dislodge the clog by blowing out debris. If the above methods are not successful, find the clog by hand, then squeeze the hose and shake until the debris dislodges. tool maintenance Keep tools clean and free of debris. 1. Wipe tools clean with damp cloth. note: the multi surface floor tool contains a strip of red material that should not get wet. If it needs cleaning, wipe with damp cloth only. SERVIcInG of DoUblE-InSUlatED aPPlIancE a double-insulated appliance is markedwith one or more of the following: thewords DoUblE-InSUlatIon or DoUblE- InSUlatED or the double insulation symbol (square within a square). In a double-insulated appliance, two systems of insulation are provided instead of grounding. no grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace. 12 800.237.7691 ug110-4053_18P0_608.indd 12 6/13/08 12:35:32 PM WaRnInG: to reduce the risk of electric shock, turn power off and disconnect polarized plug from electrical outlet before performing maintenance ortroubleshooting. Troubleshooting Vacuum cleaner won’t turn on Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker in home 2. Check/replace fuse or reset breaker 3. Thermal protector activated 3. Allow cleaner to cool for 30 minutes, see pg 8. This will reset thermal protector 4. Dirt tank is full of water 4. Empty tank and reattach 5. Dirt tank is full of debris 5. Empty tank and reattach Vacuum cleaner and tools won’t pick up or low suction Possible causes Remedies 1. Hose not properly positioned 1. Make sure hose is fully connected to base 2. Dirt tank not installed properly 2. Check assembly of upper and lower portions, correctly position and secure into place 3. Dirt tank full 3. Empty dirt tank 4. Clog in cleaner 4. Follow instructions on pg 11 and 12 for clearing clogs 5. Filters are dirty 5. Check and clean filter 6. Hose not properly attached 6. Make sure hose collar is pushed in or in locked position 7. Vacuum is not suctioning or blowing 7. Make sure hose is in correct inlet/outlet other maintenance or service not included in the manual should be performed by an authorized service representative. thank you for selecting a bISSEll product. If you should happen to need assistance during assembly or operation, call 1-800-237-7691. Please do not return this p...

Herunterladen

Geben Sie zwei Ziffern: