Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
• Properly clamp material to avoid movement and vibration. MAINTENANCE Motor Brush Inspection andReplacement (Fig. 10) WARNING: Turn off and unplug the tool. Be sure the trigger switch is in the OFF position. Brushes should be regularly inspected for wear. To inspect brush- .3" (8mm) Y W X Y .3" (8mm) Y W X Y centers or other qualified service organizations, FIG. 10 Z tical replacement parts. NOTE: Unit may be converted to a 3-wire twist lock authorized service center. Lubrication Closed-type, grease-sealed ball bearings are used These bearings have sufficient lubrication packed in them at the factory to last the life of the chop saw. Accessories CAUTION: The use of any other accessory not recommended for use with this tool could be hazardous. Use only high-strength Type 1 organic bonded wheels rated 4100 rpm or higher. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating your local dealer or authorized service es, unscrew the two end cap screws (W) and remove end cap (X). center contact: DEWALT Industrial Tool Co., 701 East Joppa Road, Remove brush cap (Z). Brushes (Y) should slide freely in brush Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258). box. If brushes are worn down to .3" (8mm) as shown in Figure 10 Three Year Limited Warranty they should be replaced. To reinstall, push new brush back into DEWALT will repair, without charge, any defects due to faulty mate- brush box. If replacing existing brush, maintain same orientation as rials or workmanship for three years from the date of purchase. when removed. Replace the brush cap ( do not overtighten). This warranty does not cover part failure due to normal wear or tool Replace end cap and two screws. Tighten securely. abuse. For further detail of warranty coverage and warranty repairCleaning information, visit or call 1-800-4-DEWALT. This warranty does not apply to accessories or damage caused where Blowing dust and grit out of the main housing by means of an air repairs have been made or attempted by others. This warranty hose is recommended and may be done as often as dirt is seen gives you specific legal rights and you may have other rights which collecting in and around the air vents. Always wear proper eye vary in certain states or provinces. and respiratory protection. In addition to the warranty, DEWALT tools are covered by our: Repairs To assure product SAFETY and RELIABILITY, repairs, mainte- 1 YEAR FREE SERVICE nance and adjustment should be performed by authorized service DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. 9 English English 10 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. RECONDITIONED PRODUCT: Reconditioned product is covered under the 1 Year Free Service Warranty. The 90 Day Money Back Guarantee and the Three Year Limited Warranty do not apply to reconditioned product. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement. Tr oubleshooting Guide TROUBLE! TOOLWILLNOT START WHAT’S WRONG? WHAT TO DO… 1. Tool not plugged in. 1. Plug in saw. 2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit breaker. 3. Cord damaged. 3. Have cord replaced by authorized service center. 4. Brushes worn out. 4. Replace brushes. TROUBLE! TOOLMAKES UNSATISFACTORYCUTS WHAT’S WRONG? WHAT TO DO… 1. Glazed wheel. 1. Dress the wheel or replace with a new one. 2. Workpiece incorrectly placed or clamped. 2. Firmly clamp and support workpiece. TROUBLE! BLADE DOES NOT COME UPTO SPEED WHAT’S WRONG? WHAT TO DO… 1. Extension cord too light or too long. 1. Replace with adequate size cord. See chart on page 1. 2. Low voltage. 2. Contact your electric company. 3. Low generator voltage. 3. Check generator output voltage. Reduce number of tools powered by the generator. TROUBLE! TOOLVIBRATES EXCESSIVELYDURING CUT WHAT’S WRONG? WHAT TO DO… 1. Tool not mounted securely to stand or work bench. 1. Tighten all mounting hardware. See page 8, Procedure for Permanent Mounting. 2. Damaged wheel. 2. Replace wheel. 3. Workpiece not clamped properly. 3. Refer to Material Clamping and Supporting page 5. 11 English English Troubleshooting Guide… TROUBLE! DOES NOT MAKE ACCURATE CUTS WHAT’S WRONG? WHAT TO DO… 1. Fence not adjusted correctly. 1. Check and adjust. See Fence Operation on page 6. 2. Wheel is not square to fence. 2. Check and adjust. 3. Excessive force used to make cut. 3. Reduce cutting force, let the wheel do the work. 4. Work piece moving. 4. Clamp workpiece securely. See Material Clamping and Supporting page 5. Make sure material is laying flat a...
Dieses Handbuch ist für folgende Modelle:Kreissägen - D28700 (1.59 mb)