Stimmen - 6, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: GBC Dateigröße: 618.32 kb Dateiname: Unterrichtssprache:

GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 18 Display Control Panel-Continued Top and Bottom Temperature Use the up or down arrow keys to increase or decrease the set temperature of the heat rollers. The temperature shown on the display is the temperature at which the unit is attempting to attain. For example if the unit is set to 200*F even though the actual roller temperature may be higher or lower. To view the actual temperature press MEASURE. Stop The STOP button ceases the forward rotation of the rollers. Reverse Pressing the REVERSE button causes the rollers to turn in the reverse direction. The rollers will only turn in reverse as long as the REVERSE button is depressed. GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 19 Display Control Panel-Continued The Temperature displayed in the area referred to as TOP TEMPERATURE and BOTTOM TEMPERATURE is the value that the laminator is attempting to attain. Pressing the MEASURE button will momentarily display the actual roller temperature. The current speed and job settings are given on the right side of the display. The current state of the heat rollers is given on the lower portion of the display. The unit will always be in one of three states: AUTO-OFF, READY, or WAIT. Auto-Off In the AUTO-OFF state (also referred to as Standby) the unit will no longer continue to heat the main rollers. The unit will go into this state after a period of inactivity or by pressing the STAND-BY key. Press the STAND-BY key to bring the unit out of AUTO-OFF mode. See Fig. A Ready The READY icon will flash when the actual roller temperature is nearing but not quite met the target temperature. The READY icon will be displayed continually when the actual roller temperature is within +/- 15* F of the target temperature entered by the operator. See Fig. B Wait The WAIT icon is displayed when the actual roller temperature is much higher or lower than the target temperature entered by the user. See Fig. C Fig. A Fig. B Fig. C GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 20 Section 8: Safety The 1244Wf & 1264 WF have numerous safety features that will help keep the operator safe from harm. But for these features to work correctly, the user must become familiar with each of the safety mechanisms as well as never override a safety feature. Emergency Stop/E-Stop Two Emergency Stops (Sometimes referred to as E-Stops) are located on the 1244 WF & 1264 WF laminators. See the “Know your Laminator” section for the locations. Pressing any one of the two Emergency Stops will immediately stop all roller motion. To reset the Emergency Stop, simply rotate the red top clockwise; this will cause the red top to pop upward and allow the rollers to turn again. Safety Shield The Safety Shield aids in preventing the operators fingers from becoming pinched or burned in the heat rollers of the laminator. With the Safety Shield raised or removed, the machine goes into the safety mode that prevents the RUN button on the control panel from starting the rollers to turn. The foot pedal must be used when the Safety Shield is raised or removed. Use caution when operating the unit with the shield removed. GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 21 Safety Shield-Continued To remove the Safety Shield, first raise the shield and locate the spring hinge pin on the right side of the shield. Pull the pin to release the shield from the laminator as illustrated in the photo. Feed Table The Feed Table supports the product to be laminated. It also prevents full access to the roller nip (where the upper and lower roller meet) of the laminator. Because of this the laminator has been designed not to operate when the Feed Table is removed. Re-install the Feed Table before attempting to operate the laminator. GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 22 Section 9: How to Guide This section discusses how to load film on the unwinds, how to center film, how to select and change the nip, how to center film, how to select and change the nip, how to use the inline slitters and rear slitter. Loading Film Begin by removing the hinge pin that prevents the film shaft from swinging outward. Swing the film shaft outward as is illustrated in the photo. GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 23 Loading Film Continued The core chucks need to be adjusted to match the width of the film that is going to be loaded on the laminator. To do this, be gin by removing the rubber o-rings. Then use the included hex tool to loosen the setscrews in the core chucks. Note: Do not remove the setscrews; they only need to be loosened. Make the necessary adjustments to the upper roll of laminate to center it to the Main Rollers. Slide the Core Chucks into place and gently tighten the setscrews to secure the Core Chuck. The rubber O-Rings can be replaced to keep the film fro...

Herunterladen

Geben Sie zwei Ziffern: