Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Dell Dateigröße: 3.98 mb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

PC Desktops - PowerEdge C6105 (2.29 mb)

PC Desktops - PowerEdge C6105 (2.85 mb)

PC Desktops - PowerEdge C6105 (2 mb)

3. At the same time, pull out the power supply by using its handle. NOTE: It takes considerable force to remove the power supply. Removing and Installing Hardware | 31 Follow these instructions to install the power supply: Insert the replacement power supply firmly into the bay. The retaining clip should snap. Fold the power supply handle down. Connect the AC power cord to the replaced power supply. Removing and Installing Hardware | 32 Power Distribution Board (PDB) Replacing Power Distribution Board (PDB) Follow these instructions to remove the PDB: CAUTION: Before you remove or install the power distribution board take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections. Failure to observe these warnings could result in personal injury or damage to the equipment. 1. Remove all power supplies from the system following the steps outlined in Section-Replacing Power supplies. 2. Loosen and remove the screws securing the middle cover. Removing and Installing Hardware | 33 3. Remove the middle top cover from the system. 4. Loosen and remove the screws securing the back cover. Removing and Installing Hardware | 34 5. Slide the cover horizontally to the back using the traction pad and remove the back cover in the direction of the arrow. 6. Then Remove the BMC LAN cable from the retention clip. Lay the BMC LAN cable across the fans out of the way. Removing and Installing Hardware | 35 7. Loosen and remove the screws securing the power supply cage. 8. Slide the power cage horizontally to the back. Removing and Installing Hardware | 36 9. Lift the power cage to remove it in the direction of the arrow. 10. Loosen and remove the screw securing the rail. Removing and Installing Hardware | 37 11. Remove the rail by lifting the retention clip and at the same time slide the rail in the direction of the arrow. 12. Loosen and remove the screws securing the PDB. Removing and Installing Hardware | 38 13. Remove the PDB in the direction of the arrow. NOTE: It takes considerable force to remove the PDB. Installing the power distribution board To install the power distribution board follow the instructions for removing the power distribution board in the reverse order. . Removing and Installing Hardware | 39 iPass Board Replacing iPass Board Follow these instructions to replace the iPass board: CAUTION: Before you remove or install the iPass Board, take the steps: 1) Make sure the system is not turned on or connected to the AC power.2) Disconnect all necessary cable connections. Failure to observe these warnings could result in personal injury or damage to the equipment. 1. Loosen and remove the screws securing the middle cover. Removing and Installing Hardware | 40 2. Remove the middle top cover from the system. 3. Loosen and remove the screws securing the back cover. Removing and Installing Hardware | 41 4. Slide the cover horizontally to the back using the traction pad and remove the back cover in the direction of the arrow. 5. Then Remove the BMC LAN cable from the retention clip. Lay the BMC LAN cable across the fans out of the way. Removing and Installing Hardware | 42 6. Pull up the power supply handle. 7. Remove the power supply in the direction of the arrow. Removing and Installing Hardware | 43 8. Loosen and remove the screws securing the power supply cage. 9. Slide the power cage horizontally to the back. Removing and Installing Hardware | 44 10. Lift the power cage to remove it in the direction of the arrow. 11. Loosen and remove the screws securing the top of the iPass connector cage. Removing and Installing Hardware | 45 12. Slide the iPass connector cage horizontally to the back. 13. Loosen and remove the screws securing the top iPass board. Removing and Installing Hardware | 46 14. Lift up the iPass board and remove it from the system. 15. Loosen and remove the screws securing the bottom iPass board. Removing and Installing Hardware | 47 16. Lift up the iPass board and remove it from the system. Installing the iPass board To install the iPass board follow the instructions for removing the iPass board in the reverse order. Removing and Installing Hardware | 48 Middle Board Replacing Middle Board Follow these instructions to replace the middle board: CAUTION: Before you remove or install the middle board, take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections. Failure to observe these warnings could result in personal injury or damage to the equipment. 1. Remove the Fan Cage. See Section-Replacing Fan Cage. 2. Remove the Power Distribution Board. See Section-Replacing Power Distribution Board 3. Remove the iPass board. See Section-Replacing iPass Board. 4. Remove the fourteen (14) screws securing the middle board in place. Removing and Installing Hardware | 49 5. Lift the middle board out of the system in the direction of the arrow, front edge first , to clear th...

Herunterladen

Geben Sie zwei Ziffern: