Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Dell Dateigröße: 3.98 mb Dateiname: Unterrichtssprache:

Removing and Installing Hardware | 45 12. Slide the iPass connector cage horizontally to the back. 13. Loosen and remove the screws securing the top iPass board. Removing and Installing Hardware | 46 14. Lift up the iPass board and remove it from the system. 15. Loosen and remove the screws securing the bottom iPass board. Removing and Installing Hardware | 47 16. Lift up the iPass board and remove it from the system. Installing the iPass board To install the iPass board follow the instructions for removing the iPass board in the reverse order. Removing and Installing Hardware | 48 Middle Board Replacing Middle Board Follow these instructions to replace the middle board: CAUTION: Before you remove or install the middle board, take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections. Failure to observe these warnings could result in personal injury or damage to the equipment. 1. Remove the Fan Cage. See Section-Replacing Fan Cage. 2. Remove the Power Distribution Board. See Section-Replacing Power Distribution Board 3. Remove the iPass board. See Section-Replacing iPass Board. 4. Remove the fourteen (14) screws securing the middle board in place. Removing and Installing Hardware | 49 5. Lift the middle board out of the system in the direction of the arrow, front edge first , to clear the IO ports. Installing the system middle board To install the system middle board follow the instructions for removing the system middle board in the reverse order. Removing and Installing Hardware | 50 Front I/O Panel Removing Front I/O Panel CAUTION: Before you remove or install the Front I/O Panel, make sure the system is not turned on or connected to the AC power. 1. Remove the screws securing the Front I/O panel cover. 2. Remove the Front I/O panel cover. Removing and Installing Hardware | 51 3. Remove the screws securing the Front I/O panel. 4. Remove the Front I/O panel and disconnect the cable. Installing the Front IO panel To install the Front IO panel follow the instructions for removing the Front IO panel in the reverse order. Removing and Installing Hardware | 52 Installing the Rail and the System Follow these instructions to install the rail into a rack: 1. Install the sliding rails into the rack. 2. Align the inner rails with the sliding rails of the rack. Removing and Installing Hardware | 53 3. Push the system into the sliding rails until the locking latch clicks into place. 4. Connect ipass connectors and power connectors. Removing and Installing Hardware | 54 NOTE: The 1400W Power Supplies require 220VAC. Removing and Installing Hardware | 55 Cable Routings 1 Fan Power Cable 2 Front I/O Cable 3 BMC LAN Cable 4 Fan LED Cable 5 PCI Power Cable 6 Switch Cable Cable Routings | 56 iPass Port Mapping 2 to 1 mode 4 to 1 mode 8 to 1 mode IPASS PCIE IPASS PCIE IPASS PCIE Mapping1 1 VS 1,15 1 VS 1,2,15,16 1 VS 1,2,3,4,13,14,15,16 5 2,16 5 N/A 5 N/A Mapping2 2 VS 3,13 2 VS 3,4,13,14 2 VS N/A 6 4,14 6 N/A 6 N/A Mapping3 3 VS 5,11 3 VS 5,6,11,12 3 VS 5,6,7,8,9,10,11,12 7 6,12 7 N/A 7 N/A Mapping4 4 VS 7,9 4 VS 7,8,9,10 4 VS N/A 8 8,10 8 N/A 8 N/A NOTE: The default port mapping is 2 to 1 mode. Cable Routings | 57 BMC Remote Management Console This chapter provides information on the various functions of the Dell Remote Management Console GUI’s (Graphics User Interface). Initial Configuration using a DHCP Server Before entering the Dell Remote Management Console, you need to connect the DHCP server in the subnet to which it is physically connected. If a DHCP server is found, it may provide a valid IP address, gateway address and net mask. Before you connect the device to your local subnet, be sure to complete the corresponding configuration of your DHCP server. It is recommended to configure a fixed IP assignment to the MAC address of the system. BMC Remote Management Console | 58 Static/DHCP IP Controlled by Front Panel Button • To switch from DHCP to static or vice versa: • Hold down the ID button for 5 seconds • While pressing the ID button, press and hold the power button for 5 seconds • Release the power button, and then the ID button • It will take ~30 seconds to change the configuration • The ID light will indicate which mode has been selected: -Solid for 5 seconds indicates static IP -Flashing for 5 seconds indicates DHCP • If the default IP address is changed, switching DHCP to static IP will change the IP address back to the default. • The default IP address is 192.168.0.120 BMC Remote Management Console | 59 Remote Management Console Overview 1. Open a web browser and type in your identified IP. The IP address can be found using your DHCP server. 2. A dialog box prompts you to enter Username and Password. 3. Enter the following values: Username: root Password: root NOTE: The default user name and password are in lower-case characters. NOTE: When you log in using the root user name and password, you have full administrative privileges. It ...

Herunterladen

Geben Sie zwei Ziffern: