Tape dubbing operation (Deck A \Deck B) CT-2050/203/KXF-W6010/W4010 (En/M) The dubbing refers to the copy of the recorded contents of a tape to another tape (tape in Deck A \tape in Deck B). Since this unit is not designed for recording with metal (TYPE ) tapes, do not use metal tapes for recording. CT-203/KXF-W4010 only CT-2050/KXF-W6010 only Preparation 1Load the tape to be played in deck A and the tape to be recorded in deck B. 02Set the tape transport directions of decks A and B to the same

OAfter completion of CCRS recording , be sure to cancel the CCRS and ensure that the CCRS indicator has gone off. NotesNotes 1. If the CCRS key is pressed during CD playback, playback stops and CCRS operation begins. 2 .If the remaining amount of tape is small, CCRS may not function correctly or CCRS operation may be canceled in mid-operation. 3 .Once the CCRS recording level has been set, the recording balance and recording level cannot be adjusted while the CCRS operation is being carried out.

It is recommended that these tapes not be used with this unit to prevent possible damage. 2. Endless tapes Do not use an endless tape, as this could damage the mecha- nism of the unit. Maintenance Demagnetizing the head When the recording / playback head is magnetized, the sound quality will be deteriorated. In such a case, demagnetize the head using a commercially available demagnetizer (head eraser). There are precisely aligned parts around the heads, including the tape guides. When cleaning,

2Start playback. CT-403 /KXF-W3030 or 2 Load a cassette tape in deck A or B. (Normal playback) Load cassette tapes in both decks. (Relay playback) 1 Set the POWER switch to ON. Press the area marked PUSH/OPEN 0. 1 Dolby NR on 2 Dolby NR off : Keys or controls to be used in this operation Normal playback (dB) — —5 0 +3 +6 (dB) TAPE B AUTO REVERSE TAPE A AUTO REVERSE POWER 1 @ 7 # @ 7 # A 1 A 8PAUSE ¦REC/ARM PUSH/OPEN 0 PUSH/OPEN 0 POWER - ON . OFF PUSH/OPEN 0 (dB)— —5 0 DOLBYNR 77 1 8P A RECL PUS

OFF 2 37 2 37 Set the record-pause mode. Press 7 key of the CD player. Press the 6 key of the CD player. 1 Play a CD. 4Put the CD player in stop mode. 3 2Set the record-pause mode. OWhile pressing the PAUSE (8) key, press theREC/ARM (¦) key. 3Adjust the recording balance and recording level. “How to record.” ^ 8PAUSE ¦REC/ARM Start playing the CD. 8PAUSE ¦REC/ARM TAPE A AUTO REVERSE TAPE B AUTO REVERSE -ON . OFF 2 37 2 37 OWhile pressing the PAUSE (8) key, press the REC/ARM (¦) key. 4 Press the

After the tape is played back to the end, it is rewound to the beginning and the playback of all selections is repeated. In the RMS play (page 50), all the selections programmed are played back repeatedly. To stop playing all selections repeatedly and return to the normal playback Press the REPEAT 1/ALL button once. The REPEAT indicator goes off. Note on the end of the repeated portion during the REPEAT ALL play The tape is rewound to the beginning of the tape when one of the following is detect

ZusatzinformationenWährend des Aufnahmevorgangs kann kein Startcodegesetzt werden.Störungsüberprüfungen/Der neue Startcode muß mindestens neun Sekunden(bzw. 18

z To use headphones Connect them to the PHONES jack. Use PHONE LEVEL to adjust the volume. 1 1 Turn on the amplifier and set the source selector to the position for DAT. 2 2 Press POWER. 3 3 Press OPEN/CLOSE ¤and insert a cassette. Window side up OPEN/CLOSE OPEN/CLOSE ¤ b b ¤ Close the cassette holder by pressingInsert the cassette OPEN/CLOSE ¤. beyond the silver bar. 4 4 Press a. The deck starts playing. Adjust the volume on the amplifier. To Press Stop playing p Go to the next track ± Go to th

Uberlassen Sie Wartungsarbeiten stets nur einem Fachmann. Herzlichen Gluckwunsch! Wir begluckwunschen Sie zum Kauf dieses Sony DAT-Decks. Bevor Sie das Deck in Betrieb nehmen, lesen Sie diese Anleitung bitte sorgfaltig durch, und bewahren Sie sie zum spateren Nachschlagen gut auf. Das DTC-ZE700 zeichnet sich durch die folgenden Merkmale aus: • High-Density-Linearkonverter Der eingebaute A/D-Impulskonverter arbeitet praktisch verzerrungsfrei und stellt einen unverfalschten Klang sicher. Der D/A-I