• The installation must conform with local codes or, in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1. • The heater and its individual shut-off valve must be disconnected from the gas supply piping system while performing any tests of the gas supply piping system at pressures in excess of 1/2 psig. • The heater must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at

The SWB400I fireplace may be installed in residential and manufactured type homes as explained by this instruction manual. The SWB400I installs with S-series chimney system components and is designed to utilize the MGD36-series of glass doors. The SWB400I can be converted to a louvered circulating unit by utilizing the MLK36 louver kit, and can utilize the FA2 fan once the fireplace has been converted to a louvered circulating unit. Natural gas or LP gas log sets may be installed in the SWB400I

Once a small hole has been made, continue tapping until you have reached sufficient diameter for the gas line to fit through. The entire knockout does not have to be removed. Install only a ..." (1 ..." max.) inside diameter approved gas line through the firebox wall for connection to the unvented room heater inside the firebox. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream of the heater to prevent moisture and contaminants from passi

A spacious viewing area and a modest footprint make this dependable unit easy to install, operate and service. Available in dedicated rear or top vent formats. STANDARD FEATURES FOR ALL UNITS: • Direct Vent Gas Fireplace • Clean viewing area • Flat louvers • Standard 36" size • New black embossed refractory comes as standard • Gas inlet flex line with shut-off valve • Includes electrical receptacle • Attached 17" low voltage wire connected to valve for remote operation hook-up • 2 piec

Btu Input: 40,000 BTU/HR Ignition System: Standing Pilot or Signature Command™ System Gas Type: Natural or LP Flue Type: Simpson Dura-Vent, Selkirk Metalbestos, MetalFab Termination: Top vent Clearance to Flue for Interior: 3" Top 1" Bottom and Sides Clearance to Flue for Outside Wall: 1" Clearance to Fireplace: 1" Minimum Vent Height Before Elbow: 24" CSA Design Certified FIELD INSTALLED ACCESSORIES Variable Thermostat Controlled Dual Forced Air Blower (160 cfm): BLOTKHL Firebrick: Cott

The decorative arch kits can not be used in conjunction with the screen panel kit. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. ACCESSORY COMPONENTS (CONTINUED) Termination Shroud Deluxe Termination Square Termination (ref. Form # 750,246M) (ref. Form # 750,055M) (ref. Form # 750,109M) Termination Guard Kits The vent termination guards may be used to cover the vent termination on the exterior of the home to minimize exposure to the hot surface of the termination. Termination Guard Kits (all

In addition a periodic visual check of the flames should be made. The pilot flame should always be present when the heater is in operation and should just envelope the tip of the thermocouple (Figure 15). WARNING: NO ADJUSTMENTS ARE TOBE MADE TO THE ODS PILOT SYSTEM. TAMPERING WITH THIS SYSTEM CANBE EXTREMELY HAZARDOUS. Standard (Manual) Version Shown Figure 15 An incorrect pilot flame is shown inFigure 16. This pilot flame will cause the thermocouple to cool. When the thermocouple cools, the he

continued on next page OPERATING INSTRUCTIONS - SIGNATURE COMMAND OPERATing INSTRUCTIONS 1. STOP! Read the safety information above. 2. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand. 3. With five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow "B" in the safety information on page 38. If you do not smell gas, go to next step. 4. Press the master switch

The hood kit replaces the standard hood that comes with these appliances and snaps into place. These kits can be retrofitted to previously installed appliances. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. ACCESSORY COMPONENTS CONTINUED Door Frame Kits (2-Piece, Top and Bottom) Two types of decorative door frame kits are available for use with these appliances - one, in polished brass finish; the other, in brushed stainless steel finish. The DTK is designed to attach directly to the front face o

Btu Input: 50,000 BTU/HR Ignition System: Standing Pilot or Electronic Gas Type: Natural or LP Flue Type: B Vent Vent Size: 8" B Vent Clearance to Flue: Specified by B Vent Manufacturer Clearance to Fireplace: 1/2" CSA Design Certified FIELD INSTALLED ACCESSORIES Bi-fold Glass Doors (Required on Propane Models): BBD4536 (Polished Brass), BLD4536 (Black) Cottage Clay firebrick Cottage Red firebrick Ambient Technologies™ Remote Controls and Thermostats -45"- -36"- _c 4-1/2" 45-1/4"