Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Monessen Hearth Dateigröße: 6.77 mb Dateiname: Unterrichtssprache:

continued on next page OPERATING INSTRUCTIONS - SIGNATURE COMMAND OPERATing INSTRUCTIONS 1. STOP! Read the safety information above. 2. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand. 3. With five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow "B" in the safety information on page 38. If you do not smell gas, go to next step. 4. Press the master switch to the "ON" (-) position. Within eight (8) seconds it will beep once. This indicates the system is ready. 5. Press "ON " button. Sparker will spark and pilot flame will light. 6. Once pilot flame is established, the main burner flame will light automatically. 7. If the pilot will not stay lit after several tries, turn the master switch to "OFF" and call your service technician or gas supplier. Master Switch OFF FP1913Switch box 8/08 FP1914Pilot w sparker 8/08 ON OFF ON Command Center TO TURN OFF GAS TO APPLIANCE 1. Turn master switch to "OFF". 2. Turn off all electrical power to the appliance if service is to be performed. SIGNATURE COMMAND SYSTEM OPERATION INSTRUCTIONS FEATURES Command Center • Easy Access Function Operation and System Configuration • Operation Confirmation/Fault Diagnostic Indications (LED/ Buzzer) • ON/OFF/HI/Med/Low Operation • Optional Wall Mounting Control Board • Electronic Ignition • Pilot Lockout safety feature • Electric Power Regeneration from Thermopile to save battery • 6-hour Automatic Shut Down Option • Convenient NG/LP Gas Type Conversion • Standing Pilot/Intermittent pilot Conversion • Previous settings Restoration Ability (Memory Off) • Uninterrupted Operation During Power Outage (Automatic Battery Backup) • ON/OFF RF Remote Receiver • Optional Transmitter Learn Capability AC Module Board (Optional, requires TSFSC Remote) • Easy Snap-on Design • Embedded Compact 120 VAC Adapter with Auto Battery Back up Feature • Remote Controlled 3-step Blower, Lighting, and On/Off Auxiliary AC Outputs Transmitter (Optional) TSFSC TSTSC TSMSC RTSC RMSC Three Flame Height Settings X X X X X Low battery Indication for Transmitter X X X X X Child Proof Lock-out X X X X X LCD Backlight X X X X X Security Codes 16 X X X X X Countdown 6 hr Timer X X X -- -- Standard Thermostatic Control Mode X X -- X -- Smart Mode Thermostat (Auto Flame & Blower Modulation) X X -- -- -- Three Brightness Settings for Lights X -- -- -- -- Three Speed Control for Blower X -- -- -- -- On/Off Auxiliary X -- -- -- -- Programmable Timer to turn blower on and off X -- -- -- -- BATTERY INSTALLATION The Command Center uses four (4) "AA" batteries as back up for power outages. The system can operate for approximately six (6) months on battery power. To Install Batteries (not included): 1. Press down the battery door tabs and pull out to remove battery door. 2. Install the batteries as indicated on Command Center. 3. Close battery door by snapping in place. 4. When the four (4) batteries are installed the system will operate without power. 5. The batteries should be replaced when the LED indicates low battery or at least once a year. To Thermopile RF Receiver ON/OFF FP1917Signature components8/08 To Sensor To Sparker NG/LP Conversion To Command Center Control Board 6 V AC Adapter To Stepper Motor To Valve OFF Command Center LED ON Master Switch Battery Door Figure 52 - Signature Command System Components SYSTEM CONFIGURATION/SETUP All System configuration/setup is done on the Command Center. NOTE: When using On/Off wall switch, the switch must be in the ON position to perform all configuration set ups at the command center. Intermittent/Standing Pilot Setup (Default intermittent) 1. Holding the ON button on the Command Center while turning on the master switch will toggle between standing pilot and intermittent pilot. 2. After the above operation, one beep (for standing pilot) or two beeps (for intermittent pilot) will be given as confirmation. Six-hour Safety Shutdown Option (Default ON) 1. The system comes preset from the factory with a six (6) hour shutdown from its last command of operation. This is done to prevent the fireplace from continuing to operate if unattended. You may disable this feature if you wish. NOTE: By disabling this feature, your fireplace may continue to operate unattended. 2. When the master switch is in the ON position (“-”), pressing the ON button and the OFF button on the Command Center simultaneously will toggle between enabling and disabling the six-hour shutdown option. 3. After the above operation, one beep (for enabling the six-hour shutdown option) or two beeps (for disabling the six-hour shutdown option) will be given as confirmation. Remote Transmitter Learn Function (Default OFF) 1. The RF receiver button located on the Control Board must be in the on position before the learn function can begin. Use paper clip to depress button. One beep for RF receiver ON or two beeps for RF receiver OFF will ...

Herunterladen

Geben Sie zwei Ziffern: