Over the years, valuable memories will occur around the warmth and comfort of your hearth. Thank you for allowing our product to be the backdrop for those special moments. 7207250100REV02 QUICK REFERENCE GUIDE FOR Compact Fireplace 1. Prior to the first use of the Compact Fireplace verify the following: • Are the circuit breakers for the unit on? • Are the light bulbs in your Compact Fireplace loose? (to check, follow the instructions for replacing the light bulbs under the maintenance section o

Replace the logset retaining screw into the ember bed. 8. Install the front door over the threaded rods, gently lifting up to engage the door into the slot in the roof. 9. Screw the two black knobs clockwise until tightened. TO REPLACE THE UPPER LIGHT BULB 1. Unscrew the two black knobs on the front of the unit by turning counterclockwise. 2. Grasp onto the front door, gently lift up and pull the door off of the unit. 3. Unscrew the bulb counter clockwise. 4. Insert new bulb. 5. Install the fron

7205780200REV01 CONTENTS PAGE 1 Important Instructions PAGE 2 Wall Mount Installation PAGE 6 Operation PAGE 7 Remote Operation PAGE 8 Maintenance PAGE 10 Warranty QUICK REFERENCE GUIDE FOR THE ELECTRIC WALL MOUNT FIREPLACE 1. Before using the electric wall mounted fireplace verify: • Are the circuit breakers for the unit on? • Are the light bulbs loose? (to check, follow the instructions for replacing the light bulbs under the maintenance section of this manual) 2. The heater may emit a slight,

OPERATION Initializing The Remote Control 1. Turn on the electrical power at the circuit breaker. 2. Slide open the battery cover on the back of the remote transmitter. 3. Install three AAA batteries into the remote control. Replace the battery cover. Note: The LCD display will flash when new batteries are inserted. 4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press any button on the remote control. The remote is transferring the code to the receiver bui

WARNING The wall mounted electric fireplace requires the wall mounting bracket screws to be installed into a minimum of one wall stud. (FIGURE 3 & 4) 1. Select the desired location near an electrical outlet. 2. Ensure the front of the unit when installed is at least 3 feet (0.9m) from combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains. 3. Mount the unit on the wall only with the bottom above an electrical outlet or a minimum of 12” (mounting bracket 34 3/4”

For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. To view the full line of Dimplex products, please visit 7206570100R09 2 Table of Contents Welcome & Congratulations. . . . . . . . . . . . . . . . . 3 Important Instructions. . . . . . . . . . . . . . . 4 Stove Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ma

3. Mark the desired location on the floor and store the fireplace in a safe, dry and dust free location. 4. Use studs to frame an opening of 24 1/2 inches (622 mm) wide X 18 1/4 inches (463.6 mm) high X 8 7/8 inches (225.5 mm) deep. Option #1 - The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace. Option #2 - A new outlet can be installed inside the new frame construction. Plug the unit into a 15Amp/120Volt outlet. If the cord does not reach, you may

Heater Control Switch Heater ON/OFF switch, activates the heater C. Fan Control Switch Fan ON/OFF switch, activates the fan (purifier). HEATER CONTROL SWITCH MAIN POWER SWITCH FIGURE 2 FAN CONTROL SWITCH WALL MOUNTED CONTROLS The fireplace can be installed with wall mounted controls. These controls include wall switches and thermostats. (see installation guide for details) A. Wall Mounted Switches This model may be installed such that a wall mounted switch activates the flame effect and a wall m

· Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 2 · Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Model And Serial Number Information

Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. FIREPLACE INSTALLATION 1. Make sure the units switched OFF (refer to section). 2. Plug the unit into a 15Amp/120VAC outlet. If the cord does not reach, you may exte