Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: CFM Corporation Dateigröße: 2.03 mb Dateiname: Unterrichtssprache:

C and D dimensions for wall/cabinet opening clearance. Units: EFJU4D0, EF0U4F0, EF0U4I0, EF0U4J0, EFJUF50 Electrical Specifications EF22 / EF26/EF26FG EF33 / EF36 Voltage 120V AC, 60 Hz 120V AC, 60Hz Total Amps 12 12.5 Total Watts 1450 1500 Heater Rating 1350 Watts 1350 Watts • Locating Your Fireplace Your new fireplace may be installed in a prefabricated cabinet available from your dealer. When choosing a location for your new fireplace, ensure the general instructions are followed. Also, for best effect install the fireplace out of direct sunlight. • Clearance to Combustibles Sides. . . . . . . . . . . . . . . . . . . .0” (0 mm) Floor . . . . . . . . . . . . . . . . . . . 0” (0 mm) Top. . . . . . . . . . . . . . . . . . . . . 0” (0 mm) Front . . . . . . . . . . . . . . . . 36" (914 mm) • Cabinet Installations Cabinets are available from your dealer which allow for fast, convenient installation of your fireplace against existing walls. For instructions on handling and assembly of your cabinet, refer to separate installation instructions that come with the cabinet. If it is necessary to secure your fireplace into a cabinet or wall opening, the following instructions apply (hardware not supplied). Remove the glass door from the unit and set aside. 3/16” (5 mm) clearance holes, two (2) per side must be drilled through the fireplace sides for #8 x 3/4” long black oxide wood screws or similar. The mounting holes can be located on left and right sides approximately 2” (51 mm) from the top and 5” (127 mm) from the bottom of the glass door area. The mounting hole location distance from the front of the unit must not interfere with the glass door and the refractory (brick pattern) when reinstalled. If necessary, modify the cabinet or wall opening for the mounting screws to attach. Double check the mounting hole’s locations on the fireplace before drilling. A small 1/16” (2 mm) pilot hole or center punch before drilling is recommended. Mark and drill from the outside to avoid marking or damaging the interior of the fireplace. Tighten the screws evenly so the unit remains centered in the opening and without distorting the sides of the fireplace unit. It is advisable to place wood shims or similar between the fireplace sides and the cabinet to prevent distortion when tightening the screws. 1/2” (13 mm) Velcro strips for securing the log to the grate tines and away from the screen are recommended. • Electrical Connection A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft. (1.8 m) long three wire cord, exiting the right side of the fireplace. Plan the installation to avoid the use of an extension cord. Extension cords are for temporary use only. If an extension cord must be used, it must be UL/CSA certified, rated at 15A (1875W), 125V maximum with 14 AWG minimum and constructed of two current carrying conductors with ground. A heavy duty extension cord with the shortest length possible for the connection is recommended and must not be longer than 50 ft. (15.2 m). Do not coil or cover the extension cord. Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to persons. Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water. • Grounding Instructions This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 1. An adapter as shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. Figure 1 Cover of Grounded Outlet Box ABCGrounding Means Grounding Pin Adapter Metal Screw • Direct (Hard) Wiring Electric Fireplace This instruction is intended as a guide for replacing the power cord supplied with Models EF22/26/33/36 electric fireplace with direct (hard) wiring. NOTE: When direct wiring this appliance, it must be connected to a 15 Amp dedicated circuit breaker or fuse in the electrical panel of the dwelling. The cable between the circuit/fuse panel and the fireplace must meet all local and national codes, and in no case shall the wires be less than 14 gauge. 1. Make sure the power to the unit has been turned off, the power cord is unplugged from the wall outlet and the unit has cooled down if it has been operating. 2. Follow Steps 3 through 6 in “Replacing Light Bulbs” section, Page 8, to gain access to control panel behind the touchpad controls. 3. Locate wher...

Herunterladen

Geben Sie zwei Ziffern: