Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: CFM Corporation Dateigröße: 2.03 mb Dateiname: 6e2020cb-96df-8d74-c1de-a3b1c8106ce0.pdf Unterrichtssprache:

Remove and discard the green wire. Reinstall the nut but do not tighten yet. 7. While standing on the right side of the unit, locate the power cord where it exits the cabinet. Using pliers, gently cut and remove the power cord. Dispose of the power cord. 8. Using a slotted screwdriver, remove the 7/8" (22 mm) diameter knockout from the right hand side of the cabinet above where the strain relief was located. 9. Route the electrical cable from the breaker/fuse panel through the 7/8" (22mm) diameter hole and secure to the cabinet using an approved clamp. The power wires should extend approximately 6" (152mm) into the control compartment. 10. Connect the ground wire from the power cable by wrapping it around the ground stud of the unit and securing it using the #6-32 nut. 11. Using a wire nut, connect the hot lead (black), of the power cable to the power cord wire that ends in 90° terminal (on the control board side, it ends on your right hand side). Similarly, connect the neutral wire (white), of the power cable to the power cord ending with the straight terminal (on the control board side, it ends on your left hand side) using a wire nut. It is recommended that the wire nuts be taped to the wires, using electrical tape, as an extra safety measure. 12. Visually check that none of the wires in the control compartment have been dislodged from the controls. If they have, use the wiring diagram on the unit or in the instruction manual to replace them in their proper location. 13. Turn the power to the unit on at the breaker/fuse panel. Place the unit into operation and check to make sure that all of the systems are working properly. WARNING: This procedure must be conducted by a qualified electrician, in accordance with National and local codes. In the U.S.A., the installation must conform to the National Electrical Code, ANSI/NFPA No. 70. In Canada, the installation must conform to the current CSA C22.1 Canadian Electrical Code. WARNING: Make sure the power to the unit is off, and the power cord is unplugged from the wall outlet before proceeding with this conversion. Failure to do so may result in property damage, personal injury or loss of life. WARNING: Make sure the power to the power cable has been turned off at the breaker/fuse panel of the residence before proceeding. Service Instructions • Remove Front Cover Access to heater/fan 1. Turn off power to the unit. 2. Let fireplace cool if it has been operating. 3. To remove the doors, locate and remove the two (2) screws holding the door at the top. (Fig. 2) Hold the door at all times with one hand to prevent the door from falling when you undo the hinge screws. 4. Locate the screws that hold the front cover in place. There are six (6) screws, three (3) located on the front of the unit (Fig. 3), and three (3) located underneath the top shelf of the unit. (Fig. 4) 5. Remove screws using appropriate screwdriver. 6. Pull out the front cover. holding both sides of the cover, pull gently towards you and down. 7. You now have access to the heater/fan unit, for cleaning and/or maintenance. 8. To reinstall the front cover, please follow reverse procedure, paying attention not to damage any wiring in the process. W A R N I N G : D i s c o n n e c t power before attempting any maintenance or clean- ing to reduce the risk of fire, electrical shock or personal injury. ........................................................ Remove Screws FP1733 Figure 2 Remove Screws FP1734 Figure 3 .......................................................... Remove Screws Figure 4 .................................................................... Figure 5 FP1736 • Glass Information 1. Under no circumstances should this product be operated with broken glass. 2. Do not strike or slam the glass. 3. Do not use abrasive cleaners to clean the glass. 4. This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by a qualified service person. • Replacing the Light Bulbs Depending on your model, the fireplace uses two (2) or three (3) clear 120 Volt, 60 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located under the ember bed. Units with overhead lights (Fig. 9) use two (2) clear 120 Volt, 5 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located above the logs. For convenience, if one of the light bulbs burns out, it may be easier to replace all of the light bulbs at the same time. Do not exceed 60 Watts per bulb for the ember bed bulbs and 5 Watts per bulb for the overhead lights. Use of higher rated bulbs may result in a fire, causing property damage, personal injury or loss of life. 1. Turn off power to the unit. 2. Let fireplace cool if it has been operating. 3. Open the front doors. 4. Locate two (2) screws that hold the refractory (brick patterned) bracket together with the ember bed. (Fig. 6) NOTE: Some units may have two (2) screws securing the refractories to the ember bed. These screws must a...

Herunterladen

Geben Sie zwei Ziffern: