Stimmen - 3, Durchschnittliche Bewertung: 5 ( )

Hersteller: CFM Corporation Dateigröße: 2.03 mb Dateiname: Unterrichtssprache:

Never locate this appliance where it may fall into a bathtub or other water container. 10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over. 11. To disconnect this appliance, turn controls to the off position, then remove plug from outlet. 12. Connect to properly grounded outlets only. 13. This appliance, when installed must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electrical codes or for USA installations, follow local codes and the National Electric Code, ANSI/NFPA No. 70. 14. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or damage the appliance. 15. To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 16. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it. 17. Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. 18. Avoid the use of an extension cord because of the risk of overheating the cord and the risk of fire. Extension cords are for temporary use only. If an extension cord must be used, it must be UL/CSA certified, rated at 15A (1875W), 125V maximum with 14 AWG minimum and constructed of two current carrying conductors with ground. A heavy duty extension cord with the shortest length possible for the connection is recommended and must not be longer than 50 ft. (15.2 m). Do not coil or cover the extension cord. Save These Instructions 10009816 5 Installation Instructions Ref. EF22 EF26/EF26FG EF33 EF36 A 23..." (597 mm) 27...” (699 mm) 34...” (876 mm) 37...” (953 mm) B 20..." (527 mm) 25...” (641 mm) 29...” (743 mm) 33...” (845 mm) C 22..." (571 mm) 26...” (667 mm) 33...” (845 mm) 36...” (921 mm) D 20" (508 mm) 24...” (622 mm) 29” (737 mm) 32...” (826 mm) E 11..." (292 mm) 11...” (292 mm) 11...” (292 mm) 11...” (292 mm) F 22" (559 mm) 18” (457 mm) 25” (635 mm) 28” (711 mm) G 21..." (540 mm) 25...” (641 mm) 32...” (819 mm) 35...” (895 mm) H 15" (381 mm) 19...” (495 mm) 22...” (578 mm) 26...” (667 mm) J 33..." (860 mm) 31” (787 mm) 36....” (916 mm) 38...” (971 mm) K 46...." (1179 mm) 43...” (1114 mm) 51” (1295 mm) 54....” (1373 mm) L 23..." (590 mm) 21.....” (557 mm) 25...” (648 mm) 27....” (687 mm) F C E A B D G H 1” (25 mm) J K L J • EF22/26/33/36 Fireplace Dimensions NOTE: Add 1/4” (7 mm) to Ref. C and D dimensions for wall/cabinet opening clearance. Units: EFJU4D0, EF0U4F0, EF0U4I0, EF0U4J0, EFJUF50 Electrical Specifications EF22 / EF26/EF26FG EF33 / EF36 Voltage 120V AC, 60 Hz 120V AC, 60Hz Total Amps 12 12.5 Total Watts 1450 1500 Heater Rating 1350 Watts 1350 Watts • Locating Your Fireplace Your new fireplace may be installed in a prefabricated cabinet available from your dealer. When choosing a location for your new fireplace, ensure the general instructions are followed. Also, for best effect install the fireplace out of direct sunlight. • Clearance to Combustibles Sides. . . . . . . . . . . . . . . . . . . .0” (0 mm) Floor . . . . . . . . . . . . . . . . . . . 0” (0 mm) Top. . . . . . . . . . . . . . . . . . . . . 0” (0 mm) Front . . . . . . . . . . . . . . . . 36" (914 mm) • Cabinet Installations Cabinets are available from your dealer which allow for fast, convenient installation of your fireplace against existing walls. For instructions on handling and assembly of your cabinet, refer to separate installation instructions that come with the cabinet. If it is necessary to secure your fireplace into a cabinet or wall opening, the following instructions apply (hardware not supplied). Remove the glass door from the unit and set aside. 3/16” (5 mm) clearance holes, two (2) per side must be drilled through the fireplace sides for #8 x 3/4” long black oxide wood screws or similar. The mounting holes can be located on left and right sides approximately 2” (51 mm) from the top and 5” (127 mm) from the bottom of the glass door area. The mounting hole location distance from the front of the unit must not interfere with the glass door and the refractory (brick pattern) when reinstalled. If necessary, modify the cabinet or wall opening for the mounting screws to attach. Double check the mounting hole’s locations on the fireplace before drilling. A small 1/16” (2 mm) pilot hole or center punch before drilling is recommended. Mark and drill from the outside to avoid marking or damaging the interior of the fireplace. Tighten the screws evenly so the unit remains centered in the opening and without distorting the sides of the fireplace unit. I...

Herunterladen

Geben Sie zwei Ziffern: