A96447 Introduction Congratulations! As the owner of Bryant’s Zone Perfect Plus zoning system, you have made a commitment to improving your indoor comfort. Zone Perfect Plus allows your heating and cooling system to follow your schedule and provide greater comfort in areas which are difficult to heat or cool. Here’s how it works: Your Bryant dealer has divided your home or business into zones which are controlled separately. Instead of setting one temperature for the entire house or business, yo

55 -- Smoke Detector Sensor Smoke Detector Locations Supply Air — The Supply Air smoke detector sensor is located to the left of the unit’s indoor (supply) fan. See Fig. 56. Access is through the fan access panel. There is no sampling tube used at this location. The sampling tube inlet extends through the side plate of the fan housing (into a high pressure area). The controller is located on a bracket to the right of the return filter, accessed through the lift--off filter panel. Smoke Detector

It is available with either of two factory-installed direct expansion coils (Model 180R- or 240R-379) or with no expansion coil as Model 450-379H. Model 180R units are equipped for use with R22 refrigerant and provide 180,000-Btuh cooling when connected with a Bryant Model 180-566 Condensing Unit. Model 240R units are equipped for use with R500 refrigerant and provide 240,000-Btuh cooling when connected with a Bryant Model 240-566 Condensing Unit. All three models have a heating input of 450.00

HRVBBLHU1150 HRVBBLHU1250 HRVBBSVC1150 HRVBBSVC1200 HRVBBLVU1150 HRVBBLVU1200 HRVBBLVU1330 Capacity — CFM @ 0.5– 0.3ESP (in. wc) 130–168 191–210 106–150 177–211 123–141 189–209 300–334 Efficiency (Sensible) — percent 32°F (0°C) –13°F (–25°C) 65 65 65 60 69 60 77 67 81 69 84 72 80 74 Efficiency (Latent) — percent @ all temperatures 0 0 0 0 0 0 0 Heat Core Exchange Area — cu ft (cu m) 120 3.4 166 4.7 90 8.4 144 13.3 144 13.3 210 19.5 210 19.5 ELECTRICAL DATA CONVENTIONAL COMPACT HIGH EFFICIENCY Mo

Dehumidistat Control — Allows the user to select the relative humidity level at which the unit would change fan speed for dehumidification in the winter months. Continuous Mode — If the relative humidity inside the building is lower than selected, air exchange occurs with the outside at low speed. If the relative humidity inside the house is higher than selected, air exchange occurs with the outside at high speed. Ensures continuous air exchange for constant air quality. Intermittent Mode — If t

The HRVB provides efficient and cost-effective heat recovery during the heating season when needed most. As temperatures drop below 23°F (–5°C), indoor air is recirculated periodically through the heat exchanger core to prevent frost from forming. Competitors’ methods of supplementary electric defrost waste energy. Unlike rotary wheel heat exchangers which mix air streams, these cross flow or counterflow heat exchangers ensure that there is no mixing of the stale air stream with the fresh outdoo

The shutter on the draft inducer should be initially set at 50% open, the cycle time at 8 minutes and the pilot draft switch on the primary control at medium. 3. We don’t recommend direct venting when corn is the primary fuel. For corn burning, the GBU070 needs a natural draft and this can only come from a vertical chimney. We do recommend stainless chimney be used when corn is the fuel. Corn, by nature, is more acidic than pellets and can eat away steel or galvanized chimney. 4. The moisture co

j Through the base connectors for gas and electric conduit/piping j Stainless steel gas heat exchanger (includes tubes, vestibule plate and collector box) j Economizer with dry bulb sensing and barometric relief j Economizer with enthalpy sensing and barometric relief j 2 position motorized outdoor air damper j Non- --fused disconnect j Powered 115- --volt convenience outlet j Non- --powered 115- --volt convenience outlet j High static evaporator fan motor j Return Air smoke detector j Supply Ai

1. Set UI control to OFF. 2. Turn off gas supply to unit. 3. Turn off electrical power supply to unit. OPERATING YOUR UNIT The operation of your unit is controlled by the Evolutiont UI. You simply program theUIand it maintainsthe indoortemperature atthe level you select. See UI manual for detailed instructions. To better protect your investment and to eliminate unnecessary service calls, familiarize yourself with the following facts: Step 1—Cooling Mode With the SYSTEM control set to COOL, your

wg)* COMPONENT CFM 4,000 4,500 5,000 5,500 6,000 6,500 7,000 7,500 8,000 8,500 9,000 9,500 10,000 10,500 11,000 11,500 12,000 EconoMi$er IV 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10 0.11 0.12 0.13 0.15 0.16 0.17 0.19 0.20 LEGEND FIOP — Factory-Installed Option *The static pressure must be added to the external static pressure. The sum and the evaporator entering-air cfm should then be used in conjunction with the Fan Performance tables to determine blower rpm and watts. Table 27 — Fan Rpm at