This warranty gives you specific legal rights. You may also have other rights which vary from state to state and province to province. Proof of purchase is required before a warranty claim will be accepted. CUSTOMER SERVICE: Toll-Free (800) 233-0268. Email: producthelp@laskoproducts.com Our Customer Service team is available to assist you with product questions, service center locations, and replacement parts. They can be reached Monday through Friday, 8am-5pm Eastern. Please have your model num

Securely tighten all (6) screws. (Figure 3) 2. Push the Fan Blade onto the Motor Shaft, centering the Hub facing away from the motor, until it stops against the shaft. (Inset A) Align Square Head Bolt with flat of the Motor Shaft. TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to securely tighten the Bolt could result in damage to the Fan and/or personal injury. 3. Hold the Front Grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten Fr

3. Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads of one end of the Threaded Pipe that will be screwed into the Motor Mounting Adapter. (Figure 1 - Inset) 4. Screw Threaded Pipe into Motor Mounting Adapter. The Threaded Pipe MUST BE screwed in at least 4 full revolutions. Do not allow Loctite #243 to dry before joining. Tighten provided 1/4” Set Screw into Motor Mounting Adapter. (Figure 1) 5. Open second tube of Loctite #243 by snapping tube neck just below end cap. Be Certain t

(Figure 2B) 10. Insert the 1/2” X 1” Hex Bolt (3/4” head) through the Motor Neck, and the Motor Mounting Adapter. Place 1/2” diameter Split Lockwasher then the 1/2” diameter Hex Nut (3/4” head) and tighten fully with 2 adjustable wrenches. 11. From the same side of the Motor Neck, insert one 1/4-20 X 1 5/8” Carriage Bolt through the Arc-Shaped Slot in the Motor Neck and Hole in the Motor Mounting Adapter. To Fasten: Place one 1/4” Flatwasher, one 1/4” Internal Tooth Lockwasher, a second 1/4” Fla

Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). 17. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET TH

com PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT. SAVE THESE INSTRUCTIONS 4 Rev. A 11/07 1 Rev. A 11/07 5084416 5084416 IMPORTANT INSTRUCTIONS - OPERATING MANUAL IMPORTANT INSTRUCTIONS - OPERATING MANUAL CEILING MOUNT INSTALLATION (Figures 1 and 2) NOTE: Distance mounted from the ceiling can be changed by using a length o

Dry all parts completely before reconnecting to power supply. CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners, etc. as they will damage the Fan. NEVER use ALCOHOL OR SOLVENTS. SERVICING: All other servicing, with the exception of general user maintenance, should be performed by an authorized service representative. Call 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m.and 5:00 p.m. Eastern for the location of your nearest service center. LUBRICATION: Precision

Be Certain to follow all warnings noted on Loctite #243 tube. 3. Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads of one end of the Threaded Pipe that will be screwed into the Motor Mounting Adapter. (Figure 1 - Inset) 4. Screw Threaded Pipe into Motor Mounting Adapter. The Threaded Pipe MUST BE screwed in at least 4 full revolutions. Do not allow Loctite #243 to dry before joining. Tighten provided 1/4” Set Screw into Motor Mounting Adapter. (Figure 1) 5. Open second tube of Locti

If they must be used, minimize the risk of overheating by ensuring that they are UL listed. Never use a single extension cord to operate more than one Fan. 11.Do not operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. Return Fan to authorized service facility for examination, electrical or mechanical adjustment or repair. 12.Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cau

Products are warranted by AirKing to the original user against defects in workmanship or materials under normal use for three years on the motor and one year on all other parts, after date of purchase. Any part which is determined by AirKing to be detective in material or workmanship and returned to an authorized service location, as AirKing designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at AirKing’s option. For limited warranty claim procedures, see P