. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Symbols used in this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Environmental symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction ............................................................3 UPS Family Range and Components . . . . . . . . . . . . . . . . . . . . . 4 13.85 in/352 mm Enclosures. .

Int. Mech. Bypass Switch Open. The internal mechanical switchgear is open. No corrective action is necessary. 990-2359A Smart-UPS® VT 10-30kVA, 200/208V and XR Battery Enclosure Operation Guide Operation – Display Messages/Troubleshooting Display Message Meaning Corrective Action Low-Battery. The UPS is in battery operation and the battery charge is low. Note: Runtime is limited in duration. Shut down the system and the load equipment or restore incoming voltage. Load Is No Longer Above Alarm Th

. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Symbols used in this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Environmental symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operation ...............................................................3 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 The Smart-UPS

Serious damage may occur if the procedure is not followed properly. • This motherboard does not support CPUs with a Vcore higher than 1.6 volts. Please make sure the CPU you are using 1.6 volts or below. Check the CPU specification before you insert it in the CPU socket. • AGP cards running at 3.3v are not supported. Only AGP cards running at 1.5v (most 4x or 8x AGP cards) are supported on this motherboard. • Please make sure that your memory modules are inserted correctly. They can go in only o

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 About this UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Unpack package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warning The UPS must be supplied from a: 208Y/120V or 220Y/127V 4W+ GND 60 Hz source. Note Power terminal lug diameter: minimum 6 mm. Torque value: 62 lbf.in/7 Nm. 1 Cable Entry Cable entry takes place from the rear of the UPS. Pull out the lower end of the handle and turn it counterclockwise to a horizontal position to open the door. Preparing for cabling (general) . Use a torx screwdriver to loosen the four M4 screws from the cable landing cover and remove. Preparing for bottom and top entry .

-UPS 1500/3000 VA 1500/3000 VA1500/3000 VA1500/3000 VA1500/3000 VA 120/230 Vac 120/230 Vac120/230 Vac120/230 Vac120/230 Vac Mod ModModModModu uuuular larlarlarlar Uninterruptible Power Supply Uninterruptible Power SupplyUninterruptible Power SupplyUninterruptible Power SupplyUninterruptible Power Supply 990-1704 01/2004 Introduction This APC Smart-UPS is a modular Uninterruptible Power Supply (UPS) for high availability applications such as data centers and mission critical processes, designed t

Set the input switch (Q001) to position 0 The red alarm LED below the display lights up and the acoustic alarm sounds for 30 seconds* *Use the key to reset the acoustic alarm Display shows Bypass operation : NO **System OFF** Bypass operation : YES Lamp indication on Bypass Panel Green light (H003) above the bypass switch handle (Q003) lights up Green light (H002) above the output switch handle (Q002) lights up Only the light (H002) above the output switch handle (Q002) is now on Display shows 9

The UPS provides continuous power from its internal battery until the utility line returns to safe levels or the battery is discharged. 1: INSTALLATION Read the Safety Instruction sheet before installing the UPS. Unpacking Inspect the UPS upon receipt. Notify the carrier if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly. Check the package contents. The package contains the UPS, four battery packs, rail kit, and a litera ture kit containing cable(s), and

Powerware® Prestige Series Installation and Operator’s Manual for IBM Applications (3000 VA) Uncontrolled Copy CHAPTER 3 INSTALLATION The following sections describe UPS storage requirements and the installation and startup of the UPS. Unpacking and Inspection Carefully unpack the UPS and battery cabinets, making sure to retain the packaging materials. Examine each unit carefully for any signs of damage and immediately notify your distributor if damage is present. For assistance with the IBM 991