Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Turn the thermostat until it ‘clicks’ off (causing the main burners to go out); note the setting where this occurs. Repeat this temperature ‘click points’ step at least three times to ensure that the shortening temperature has stabilized. Measure the temperature of the shortening by inserting an accurate thermometer about 4 inches into the shortening to measure its temperature. If the temperature variation between the measured temperature and the thermostat setting is 10°F or less, the thermostat can be recalibrated. FR FRFRFRFRFRYER YERYERYERYERYER TR TRTRTRTRTROUBLESHOO OUBLESHOOOUBLESHOOOUBLESHOOOUBLESHOOOUBLESHOOTING GUIDE TING GUIDETING GUIDETING GUIDETING GUIDETING GUIDE (Continued) PROBLEM Liquid shortening does not reach the desired temperature for frying. (Continued) Basket does not lower, when the timer control pushbutton is pressed after the timer control knob is set to a time value. CAUSE 3. Loose knob on thermostat; or thermostat requires calibration (temperature setting differs by about 10°F from measured shortening temperature). (Continued) 4. Thermostat setting is more than 20°F different than measured shortening temperature. 1. Electric power circuit breaker not switched ON. 2. Electric power cord not plugged into its receptacle. 3. POWER Switch not switched ON. 4. Loosened wiring connections. 5. Timer has failed. REMEDY 3. (Continued) Recalibrate the thermostat by: (a) removing the cap on the thermostat control knob; (b) loosening the center brass hex nut portion of the knob; (c) turn the pointer portion of the knob to the measured temperature value of the thermostat settings. Tighten the brass hex nut to lock the adjustment. Replace the cap on the knob. 4. Check the thermostat setting against an accurate measure of the shortening temperature. If the temperature difference is greater than 20°F, the thermostat can possibly be recalibrated. Recalibrate the thermostat by: (a) removing the cap on the thermostat control knob; (b) loosening the center brass hex nut portion of the knob; (c) turn the pointer portion of the knob to the measured temperature. Tighten the brass hex nut to lock the adjustment. Replace the cap on the knob. If this calibration is unsuccessful, the thermostat has failed and must be replaced. 1. Switch the circuit breaker to ON. 2. Plug in the power cord. 3. Switch the POWER switch ON. 4. Check wiring and tighten all connections, especially to the basket lifting devices (timer, microswitch, and motor). 5. Set a time value using the timer control knob; press the push FR FRFRFRFRFRYER YERYERYERYERYER TR TRTRTRTRTROUBLESHOO OUBLESHOOOUBLESHOOOUBLESHOOOUBLESHOOOUBLESHOOTING GUIDE TING GUIDETING GUIDETING GUIDETING GUIDETING GUIDE (Continued) PROBLEM CAUSE REMEDY Basket does not lower, 5. Timer has failed. (Continued) 5. (Continued) when the timer control button to start the timer operapushbutton is pressed tion. If the basket does not after the timer control lower into the kettle, the timer knob is set to a time has failed and must be value. (Continued) 6. Microswitch (controlling the lift motor) has failed. replaced. To confirm that the timer is defective, connect a wire as a short circuit between the wire terminals marked “C” (white wire) and “NO” (left motor: blue wire; right motor: brown wire) on the respective timer. If the lift motor now operates to lower the basket, the timer has failed and must be replaced. If the lift motor still does not operate, the microswitch or the motor may have failed. Refer to Cause 6 of this problem. 6. Set a time value using the timer control knob; press the push- button to start the timer operation. Check for 120-volt power by measuring between the “C” terminal (white wire) and the “NO” terminal (left motor: black wire; right motor: brown wire) of the microswitch. If no 120-volt power is present between these respective terminals, the microswitch is defective and must be replaced. If 120-volt power is present, but the motor still does not operate, the motor has failed and must be replaced. Basket does not raise, 1. Lifting mechanism or motor has failed. 1. If the motor operates, but the after the timer control basket doesn’t raise, observe knob reaches a timer whether the motor crank value of 0 (zero). assembly moves. If the motor crank assembly does not move, yet the motor shaft is turning, the shear pin in the motor shaft is broken and must be replaced. FR FRFRFRFRFRYER YERYERYERYERYER TR TRTRTRTRTROUBLESHOO OUBLESHOOOUBLESHOOOUBLESHOOOUBLESHOOOUBLESHOOTING GUIDE TING GUIDETING GUIDETING GUIDETING GUIDETING GUIDE (Continued) PROBLEM CAUSE REMEDY Basket does not raise, 1. Lifting mechanism or motor has failed. 1. (Continued) after the timer control (Continued) If the motor operates, but the knob reaches a timer motor shaft is not turning, the value of 0 (zero). 2. Microswitch has failed. 3. Timer has failed. gear inside the lift motor has failed and the lift motor must be replaced. If the motor does not operate, check for 120-volt power be...
Dieses Handbuch ist für folgende Modelle:Friteusen - MX-14-2E (165.73 kb)
Friteusen - MX-14AA (165.73 kb)
Friteusen - MX-14E (165.73 kb)
Friteusen - MX-7E (165.73 kb)