Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Anetsberger Brothers Dateigröße: 165.73 kb Dateiname: 745a8b3f-3811-448c-ac6e-280b0da9354e.pdf Unterrichtssprache:

** - Basket Lift Frame for MX-14AA, MX-14-2AA, or MX-7A only. NOTE: Other available optional equipment may include a sediment tray; a microprocessor-based cooking computer with shortening melter, boil-out mode, and digital timers (Fri-tronic®); a built-in filter system (Filtronic™ II or Filter Mate™); a fryer cover; a drain table; a front drain tray; or four casters. NOTE: A Parts List for each Anets Fryer is among the items shipped with each fryer. If an additional copy of this list is needed, please contact the factory as directed on the back cover. FRYER GAS SUPPLY SPECIFICATIONS Please make sure that your desired fryer location has gas supply factors that are suitable for this product: Models MX-14E, MX-14-2E, MX-14AA, &MX-14-2AA INPUT REQUIRED: 111,000 BTU/Hr * Natural Gas Propane Gas MANIFOLD PRESSURE 3.“ W.C. ** 10“ W.C. SUPPLY PRESSURE*** 6“ W.C., minimum 11“ W.C., minimum Models MX-7E & MX-7A INPUT REQUIRED: 55,000 BTU/Hr * Natural Gas Propane Gas MANIFOLD PRESSURE 3.“ W.C. ** 10“ W.C. SUPPLY PRESSURE*** 6“ W.C., minimum 11“ W.C., mini * -BTU/Hr Rating is based on sea level operation. For sites above 2000 feet, reduce this rating 4% for each 1000 feet above sea level. ** -“W.C. = Inches, Water Column. *** - Measure Supply Pressure when all other gas-powered equipment is operating. Gas Supply Inlet Pipe must be .” NPT (National Pipe Thread) standard gas line. The gas supply inlet line should be as straight as possible (fewest bends or elbows) to obtain the highest available gas pressure at the appliance. Locate this inlet line horizontally at the center of the desired fryer location, approximately 8.” above the floor. NOTE: Using a flexible inlet line permits variation in the gas supply line location, both horizontally and vertically. Anets fryers are only for use with the type of gas specified on the spec plate. If a fryer requires modification to use a gas other than that which is identified on the fryer spec plate, contact your Anets representative or call (800) 837-2638. FRYER ELECTRICAL SPECIFICATIONS Please make sure that your desired fryer location has electrical supply factors that are suitable for this product: 120 Volts, 60 Hz, (Refer to Table 1 for amperage requirements), 1-phase, three-wire connection, including an electrical ground, via a dedicated circuit breaker. A model-specific electrical circuit diagram is mounted inside the front door of each fryer. Table 1. Fryer Amperage Requirements Model Amperage MX-14E 2 A. MX-14-2E 4 A. MX-7E 2 A. MX-14AA 7 A. MX-14-2AA 9 A. MX-7A 5 A. Install a dedicated, three-prong, outlet/ receptacle within 5 feet of the desired fryer location to allow the fryer’s power cable to be connected. Ensure that the green (ground) wire of the fryer’s power cable is attached to the fryer’s structure, providing an electrical ground in accordance with applicable local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 (latest edition) or the Canadian Electrical Code, CSA C22.1 (latest edition) and CSA C22.2 (latest edition). Figure 1 is the basic wiring diagram of an MX-series fryer showing a typical circuit. Some fryers may have other options that do not appear in this basic wiring diagram. A model-specific wiring diagram included with each fryer shows all the actual parts and their associated wiring connections. In addition, fryers equipped with a built-in filter system (Filtronic II or Filter Mate) and/or built-in computer controls (Fri-tronic) have a supplementary manual included for each option. Figure 1. Fryer Model MX-14E Wiring Diagram ! WARNING Electrical Grounding Instructions (See inside of door for wiring diagram.) This appliance is equipped with a three- prong (grounding) plug for your protection against shock hazard, and should be plugged directly into a properly grounded, three-prong receptacle. DO NOT cut or remove the grounding prong from this plug. CODE REQUIREMENTS CODE REQUIREMENTSCODE REQUIREMENTSCODE REQUIREMENTSCODE REQUIREMENTSCODE REQUIREMENTS IMPORTANT: Read the Code Requirements and the Installation Requirements and Iinstructions carefully, before starting the installation. Contact the factory (800/ 837-2638) if any problems or questions arise. The fryer installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition); the Natural Gas Installation Code, CAN/ CGA-B149.1 (latest edition); or the Propane Gas Installation Code, CAN/CGA-B149.2 (latest edition), as applicable, including: a. Disconnect the fryer and its individual shutoff valve from the gas supply piping system during any pressure testing of the gas supply system at test pressures in excess of . psig (3.45 kPa). b. Isolate the fryer from the gas supply piping system during any pressure testing of the gas supply system at test pressures equal to or less than . psig (3.45 kPa). c. For fryers utilizing floor casters, the fryer installation shall be made with a connector ...

Herunterladen

Geben Sie zwei Ziffern: