• A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. MAINTENANCE 001145 1 1. Limit mark 001903 1 2 1. Brush holder cap 2. Screwdriver • Always secure small workpieces in a vise or similar hold- down device. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. CAUTI

11. 8 PRODUCT FEATURES 1. WARNING! NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 13. Always make sure the Rocker Switch (39) of the Impact Wrench is in its “OFF” position and the tool is unplugged from its electrical outlet prior to making any adjustments to the tool. (See Figure D.) Note: When your finger is off the Rocker Switch (39), the tool is in the “OFF” position. 2. Rocker Switch (39): The Rocker Switch is operat

Reversing switch lever 2. Clockwise 3. Counterclockwise 001895 Reversing switch action This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes t

Insert the cartridge fully into the port so that it rests on the charger port floor. 3. When the battery cartridge is inserted, the charging light 1. Battery cartridge 2. Button 1 2 1. 2. 1. Battery cartridge 2. Charging light 3. Battery charger 1 2 3 color will change from green to red and charging will begin. The charging light will remain lit steadily during charging. 4. When the charging light color changes from red to green, the charging cycle is complete. 5. If you leave the battery cartri

SERIAL NO. INTL. LAST NAME / COMPANY NAME STREET ADRESS CITY STATE AGE: ZIP CODE PHONE AREA CODE STATUS Married SEX M FSingle MONTH DAY YEAR Under 19 20-29 30-39 40-49 50-60 Over 60 Please return this portion by facsimile or mail. Facsimile No: (714) 522-8133 Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO LOUISIANA NEW YORK PUERTO R

Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. MADE IN CHINA For technical questions and replacement parts, please call 1-800-222-5381. Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO. INC, Product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to bec

Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Avoid unintentional starting. Be sure the trigger is not depressed when carrying the Air Hammer. 12. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate p

50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended SPECIFIC SAFETY RULES USB004-2 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to screwdriver safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 3. Hold the tool firmly. when performing an operation where the 4. Keep hands awa

have to be plugged into an electrical out- Contact with a “live” wire will also make let. exposed metal parts of the tool “live” and 3. Always be sure you have a firm footing. shock the operator. 4. Be sure no one is below when using the tool in high locations. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Do not leave the tool running. Operate the tool only when hand-held. 8. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot

Made in China For technical questions and replacement parts, please call 1-800-222-5381. Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., Product! For future reference, please complete the owner's record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire instruction sheet to become familiar with this product before you begin using it. This product is designed for certain applica