Note: The charger will not charge a battery pack if the pack temperature is below approximately 32°F (0°C) or above 122°F (50°C). The battery pack should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down. 2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or ba

• Use only under adult supervision, keep out of the reach of children. • Ensure outlet is secured and completely intact. Do not plug charger into a loose wall outlet. IMPORTANT CHARGING NOTES • While charging, the charger transformer may hum and batteries and charger become warm. This is a normal condition and does not indicate a problem. • If a battery does not charge properly— (1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected

The RBRC™ program provides a convenient alternative to placing spent nickel-cadmium battery packs into the trash or municipal waste stream which is illegal in some areas. The RBRC™program makes it easy for you to drop off the spent battery pack at local retailers of replacement nickel-cadmium batteries. You may also contact your local recycling center for information on where to return the spent battery pack. RBRC™ is a trademark of the Rechargeable Battery Recycling Corporation.. Battery Remova

Removing broken blades from the Quik-Lok® Blade Clamp Unplug the tool before removing blades. Broken blades can be removed by the following methods. • Point the tool downward, twist the collar, and shake the tool up and down (DO NOT turn the tool on while your fingers are holding the blade clamp open). The shank of the broken blade should drop out of the clamp. • If shaking the tool doesn't work... In most cases, a corner of the broken blade will extend beyond the blade clamp. Simply twist the c

We will repair without charge, any defects due to faulty material or workmanship. Please return the complete unit, transportation prepaid, to any Black & Decker Service Center or Authorized Service Station listed under “Tools Electric” in the yellow pages. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. IMPORTANT! To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush replacement) should b

(see back page). GROUNDING These units are equipped with approved 3-conductor cord and 3-prong grounding type attachment plug to be used with the proper grounding type receptacle, in accordance with the National Electrical Code and Canadian Electrical Code. IF YOUR UNIT REQUIRES LESS THAN 150 VOLTS IT HAS A PLUG THAT LOOKS LIKE FIG. “A”. It will fit directly into the proper type of 3-wire grounding receptacle. The unit is then grounded automatically each time it is plugged in. Shown in Fig.

Newarlrl>7104, 868 Broadway........................201 HU 3-1076 NEW MEXICO: - Albuquerque 87110, 4700 Lomas Blvd. N.E...505 265-6401 NEW YORK: Buffalo 14209, 881 W. Deiavan Ave.................716 TT 4-6220 New York 10462, 1894 E. Tremont Avenue (Bronx)............212 SY 2-2700 Hew York 10014, 227 Varick St. (Manhattan)....................212 WA 9-6450 New York 11377, 56-15 Queens Blvd. (Woodside)............212 DE 5-1042 Rochester 14620, 476 Clinton Ave. S................................

Keep it out of oils and greases which ruin the rubber. Coil it neatly when not in use and avoid dragging it across sharp surfaces or using it as a handle to lift the tool. When using the tool at a considerable distance from power source, an extension cable of adequate size must be used to prevent loss of power and over-heating. Use the table below for 115-volt tools. For 220-volt tools, use wire size corresponding to an extension length of y2 the contemplated length. Ampere rating 0 to 2.10 to

Some of these are listed below, but for the very many other types and sizes of accessories please see your Black & Decker Distributor, or refer to Black & Decker Catalog No. 1. SQUARE DRIVE SHANKS — ■ 1/4" HEX DRIVE SHANK . No. 20510 2" Overall Length, For %" Square Drive Sockets No. 20511 6" Overall Length, For *4" Square Drive Sockets PHILLIPS HEAD BITS — l

740228-02 (APR83-CD) Printed in U.S.A. ► Black s Deo ken OWNER’S MANUAL Your Black & Decker Electric SCRUGUN® is a heavy-duty tool, capable of continuous production service on assembly operations«. For disassembly work, there is a reversing switch conveniently located on the handle back, opposite the trigger switch. A wide variety of y4” hex drive accessories—bits, sockets, nutsetters, extensions, etc., permit this tool to drive or remove many types of threaded fasteners. For personal safety