101A393 DEC, 2005 English English Swing Door Opener USER'S INSTRUCTIONS CONTENT CONTENT Introduction.......................................................................................................................................................................................4 Overview.....................................................................................................................................................................................4 Installation - In Swing.

3.2 Place the operator onto the mounting plate based on the door type. For instance, for in-swing left door, the “IN-SWING LEFT” holes should match the 2 top holes of the operator. 3.3 Secure the operator to the mounting plate with 6 nuts, spring washers and bolts. Slider bracket Note: In-Swing right door installation shown. Note: In-Swing left door installation shown. For In-Swing Left installation, place the top 2 screws of the door opener to these 2 holes. WARNING To avoid possible serious in

First use the double sided tape to attach the mounting bracket on the windshield or use the visor clip to clip the mounting bracket on the visor, then you can put the remote control on the bracket. The remote control can also be attached to your key ring as a key fob. 7. TRANSMITTER MOUNTING METHOD 6. Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes. LED 2. RECEIVER INSTALLATION (CONT) If the Smart ButtonTM GB-318’s red LED do

In this package, you will find the following: Crimper Garage Door Transmitter MK-318 (Battery inside) Unplug the power cord of your garage door opener before installation to ensure power is not connected. DO NOT let children use the gargae door Transmitter without adult supervision. Children can injure themselves or others by the garage door. WARNING DO NOT use remote to control the door without safety beams. 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall b

Easy ClipTM Ribbon Wires Wall Button Ribbon Wires Press / lock 3. Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”. 4. If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button. a) Disconnect the existing wall button from the wall. b) Conne

This is a kit with a universal remote control and Smart ButtonTM. In this kit, you will find the following: Unplug the power cord of your garage door opener before installation to ensure power is not connected. DO NOT let children use the gargae door Transmitter without adult supervision. Children can injure themselves or others by the garage door. DO NOT use remote to control the door without safety beams. 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall but

This is a kit with a universal remote control and Smart ButtonTM. In this kit, you will find the following: Remote Control (Battery included) Visor clip 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console. 2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”. NOTE: Ensure the ribbon wires are not twisted but laid flat inside the clip. If your wall button ribbon wires are not the same

Wireless Switch ReceiverGarage Door Mounting Bracket Clip Keychain Transmitter (Battery inside) Receiver Red/Black Wire 2. INSTALLATION OF GARAGE DOOR RECEIVER The following instructions will show you how to install the receiver. After installing, the keychain transmitter (already programmed to the receiver) can be used to operate your garage door opener. You need to locate 2 things inside your garage to install the receiver: 1) the wall-mounted door control; 2) an electrical outlet, select an e

Garage Door Transmitter (Battery inside) Mounting Visor Clip Double Bracket Sided Tape There are three buttons on transmitter G6T3, each button can be programed to control Skylink garage door receiver Smart ButtonTM GB-318 or GB-318-3 or Skylink garage door opener directly. Follow one or more instructions below in Section 2 to program transmitter G6T3 to the receiver or receivers you want to control. 2a. PROGRAM TRANSMITTER TO RECEIVER GB-318 You need to do the programming in order to add the tr

INSTALLATION In this package, you will find a transmitter with 12V alkaline battery and a mounting bracket, a garage door receiver, a red / black wire. The following instructions will show you how to install the receiver. After installing, the transmitter (already programmed to the receiver) can be used to operate your garage door opener. You need to locate 2 things inside your garage to install the receiver: 1) the wall-mounted door control; 2) an electrical outlet, select an electrical outlet