Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
INSTALLATION In this package, you will find a transmitter with 12V alkaline battery and a mounting bracket, a garage door receiver, a red / black wire. The following instructions will show you how to install the receiver. After installing, the transmitter (already programmed to the receiver) can be used to operate your garage door opener. You need to locate 2 things inside your garage to install the receiver: 1) the wall-mounted door control; 2) an electrical outlet, select an electrical outlet different from the one already connected to the power cord of the garage door opener to reduce the chance of interference. The further distance between the receiver and the garage door opener, the less interference between 2 devices. Note: The length of the red/black wire is 20ft, so the receiver must be plugged into an electrical outlet that is within 20ft of the wall mounted door control. If there is no electrical outlet within 20ft of the wall mounted door control, an extension cord can be used for temporary installation. 1 Remove the wall-mounted door control from the wall by removing the screws. Connect the stripped ends of the Red/Black wire to the 2 terminals (2 screws) on the back of the wall mounted door control. (Polarity does not matter.) Unplug the power cord of your garage door opener before installation to ensure power is not connected. Wall Mounted Door Control Electrical Outlet 2. INSTALLATION (CONT) 2 3 4 5 WARNING Remove power cord of garage door opener before installation. Red / Black wire Note: There should be another pair of wires connected to the 2 terminals already. Do not remove/ disconnect these existing wires. Note: If you see no screws mounting the wall mounted door control, the screws are probably underneath the front cover. Remove the front cover by pressing onto the tabs on top of the cover. Remove front cover first 3. TROUBLE SHOOTING Q: Door opener does not react after pressing the button on the transmitter ? A: - Ensure when the button on the transmitter is pressed, the red light on the bracket comes on. Otherwise, check if the battery is inserted properly. - If the red light on the receiver flashes when you press the button on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control. - Ensure the wires that are previously connected to the wall mounted door control are not loose. - Ensure the transmitter has been programmed to the receiver. Refer to section 4 for how to program a transmitter to the receiver. Existing wires RED/BLACK WIRE RECEIVER Existing wires connected to garage door opener. (Do not remove) Different wall-mounted door controls Note: Alternative wiring options are available, the receiver can be connected directly to the opener’s motor. Please contact customer service for further information regarding alternative wiring options. Red/Black Wire Plug in the connector end of the Red/Black wire to the MT-18R receiver. Note the orientation of the male & female connector. Plug the receiver into an electrical outlet inside the garage. The red light on the receiver should be on after being plugged into an electrical outlet. Re-connect the power cord of the Garage Door Opener. The transmitter has been programmed to operate the receiver. Activate the button on the transmitter will trigger the receiver therefore opens the garage door. Garage Door Receiver 6 The activation switch and its bracket can be installed on the handlebar of your motorcycle. Remove the screw from the mounting bracket and place the cushion (included) between the mounting bracket and the handlebar. Adjust the tightness of the mounting bracket so it is securely fastened on the handlebar, then fasten the screw on the mounting bracket. You may now attach the transmitter unit to your motorcycle by hook and loop (included). It is recommended to place the transmitter unit at where it will not be exposed to water. Activating the switch on the mounting bracket will cause the transmitter to transmit a signal to the receiver. Keychain Transmitter (Battery inside) Attach the transmitter on your motorcycle Mount the bracket on the handlebar 1 0 2 0 3 0 40 5 0 6 070 8 0 90 1 0 0 1 0 7 44.. PPRROOGGRRAAMM AA TTRRAANNSSMMIITTTTEERR TTOO TTHHEE RREECCEEIIVVEERR 9.. FFCCC The transmitter in this kit has been programmed to the receiver in the factory. You need to do the programming only if you add additional transmitters to the receiver. Learn Button 2 1 3 4 Plug the receiver into an electrical socket. Press and hold the learn button on the left hand side of the receiver. The red LED on the receiver will flash. Press the button of the transmitter you want to program to the receiver. The receiver red LED will go off indicates the programming is completed. 5. REMOVE TRANSMITTER FROM THE RECEIVER You can delete the transmitter from a receiver. 2 1 Unplug the receiver from the electrical socket. Press and hold the learn but...