Stimmen - 5, Durchschnittliche Bewertung: 3.4
(
)
)
|
Anleitung Zusammenfassung
3.2 Place the operator onto the mounting plate based on the door type. For instance, for in-swing left door, the “IN-SWING LEFT” holes should match the 2 top holes of the operator. 3.3 Secure the operator to the mounting plate with 6 nuts, spring washers and bolts. Slider bracket Note: In-Swing right door installation shown. Note: In-Swing left door installation shown. For In-Swing Left installation, place the top 2 screws of the door opener to these 2 holes. WARNING To avoid possible serious injury from a falling door operator, fasten it securely to the mounting plate and the supports of the door. IN-SWING RIGHT IN-SWING LE FT OUT-SWING RIGHT OUT-SWING LEFT Top 2 screws match the 2 holes with marking "IN SWING RIGHT". INSTALLATION - IN SWING 7-1/2" (Approx. 190mm) x6 x6 x6 Actual size Remove side cover Remove side cover OPERATION Open / Close Mode When Open / Close mode is selected, the function of the 4-button remote will be different. 2 of the buttons will open the door, the other 2 buttons will close the door. To enable the Open / Close mode: 1. Unplug the door opener when it is in standby mode. 2. Change the setting of the mode selection switch to “Open / Close” mode. 3. The door opener is now operating in “Open / Close” mode. A 4-button remote control allows you to operate 2 different door openers. If you would like to operate Door 1, both the open and close buttons of door 1 must be programmed to the door opener. Follow the instructions for “Learning Remote Controls” on page 28. If you would like to operate another door opener using the same remote, learn the other 2 buttons to the other door opener. After learning the buttons to the door opener, pressing the open button will open the designated door opener. Pressing the close door button will close the designated door opener. Door 1 Door 2 Open Close Open Close Middle position - "Open/Close". Toggle Mode Toggle mode allows one button operation, which means by activating the remote, the door will either open or close, depends on the current door position. If the door is currently opened, activating the remote will close the door. If the door is currently closed, activating the remote will open the door. The same operation is used for most garage door openers. For Toggle mode, the operating mode switch should be in the lowest position. –29– Lowest position - "Toggle mode". –11– 4. Selecting the door type You must select whether you have an inswing left or inswing right door. Follow the procedures below to set the correct door type. 4.1 Before powering up the operator, the proper door configuration must be selected. To select the door type as in-swing right, please set “Door Type” slide switch to the lowest position. To select the door type as in-swing left, please set “Door Type” slide switch to the highest position, which represents in-swing left door configuration. 4.2 Before the adapter is plugged in, press and hold the "Door Setting" button (red color button). While holding down the "Door Setting" button, plug in the power adapter to the adapter socket on the door operator. Red LED will be on and the orange LED will flash rapidly and the buzzer will beep rapidly. You may now release the “Door Setting” button. 4.3 Once the button is released, the orange LED will flash slowly and the operator’s shaft will start to rotate and perform a routine startup procedure automatically in order to set itself up for this door type. 4.4 When the startup procedure is completed, you will hear 2 beeps, and the motor will stop. 4.5 You should now disconnect the power adapter from the operator and proceed to the next step. The power adapter should not be connected again until step 7. 4.6 You may now install the 2 side covers to the operator by sliding them onto the side of the operator. CAUTION When the operator is in "Door Setting" mode. The motor and its shaft will rotate. ENSURE NOTHING IS TRAPPED BETWEEN THE SHAFT AND THE OPERATOR. INSTALLATION - IN SWING Door Setting Button (red) 5. Mounting the operator assembly with mounting plate onto the door 5.1 You may now mount the operator with the mounting plate on the door. It should be mounted on the upper left corner of the door for in-swing right, or upper right corner for in-swing left. OTODOR TM Note: In-Swing Right door installation shown. Note: In-Swing Left door installation shown. OTODOR TM In Swing Right Adapter socket In Swing Left Step 1) Press and hold the door setting button. (red) Step 2) Plug in the adapter, buzzer will beep rapidly. –28– OPERATION Advanced programming / operations You have successfully setup the swing door opener and it can perform all the basic operations. There are some advanced features that require additional programming. If you would like to enable these features, follow the instructions below. These additional features / programming are: - Learn / Erase remote - Different operating modes Learn remote controls You can program up to 15 single button - remotes to the swing door opene...
Dieses Handbuch ist für folgende Modelle:Safety Gate - DM-100 (820.99 kb)