Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Easy ClipTM Ribbon Wires Wall Button Ribbon Wires Press / lock 3. Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”. 4. If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button. a) Disconnect the existing wall button from the wall. b) Connect the 2 wires from the Smart ButtonTM GB-318 to your existing wall button. Polarity does not matter, so simply pick one wire from the Smart ButtonTM GB-318 and connect it to one of the screw terminals on your wall button. Connect the 2nd wire to the other screw terminal. c) Reconnect the wall button back. 2. RECEIVER INSTALLATION Rating of the transformer: 12V DC, 100mA Diameter of DC plug : 3.5mm 7. Secure the Smart ButtonTM GB-318 properly with the mounting accessories. Note: Do not cut the antenna! Straighten up the antenna to improve signal reception. 5. If the wall button wires are hidden inside the wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door opener. Note: After installation of the “Easy Clip TM ”, if you want to re-install the Smart Button TM GB-318 to another place, please open the “Easy Clip TM ” by gently unlocking the two buckles with a screw driver, and remove it from the wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it. 6. Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes. 2. RECEIVER INSTALLATION (CONT) If the Smart ButtonTM GB-318’s red LED does not flash after the Smart ButtonTM GB-318 has been connected to the wall button’s wires for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM GB-318 will still work if you plug in an adapter (purchased separately). Please contact Skylink® to purchase the adapter. Antenna You need to do the programming in order to add the transmitter to a receiver. 3. PROGRAM KETPAD TRANSMITTER G6K TO RECEIVER GB-318 Smart ButtonTM GB-318 can learn up to 10 remote controls. To add remote controls, follow the instructions below: 1. Press the learn button on the side of the Smart ButtonTM GB-318. 2. Once the learn button is pressed, the LED will flash quickly. Release the learn button. 3. Enter [PIN][#][assigned number of door] on the keypad transmitter you would like to program. The assigned door number can be either 1, 2, 3, or 4. 4. Once the keypad transmitter is programmed, the LED will flash slowly, in the same way as it flashes in standby mode. 5. You may now operate the garage door opener with this new keypad transmitter. Learn Button Smart ButtonTM GB-318 If the red LED flashes slowly, the Smart ButtonTM GB-318 is in standby mode. When a valid remote control signal is received, it will open / close the garage door. Press the programmed button on the remote control or Smart ButtonTM GB-318, it will open / close the garage door. Note: After connecting this NEW Remote Control to your wall button, your existing remote control will still work with this connection. OPEN / CLOSE Button 4. OPERATION LED LED Crimper Double Sided Tape Garage Door Receiver Smart ButtonTM GB-318 44.. OOPPEERRAATTIIOONN ((CCOONNTT)) 88. AADDDIITIONAALL TRRANSSMMITTTTERR The keypad transmitter can operate up to 4 Smart ButtonTM units, that also means one keypad transmitter can operate up to 4 garage door openers. Same PIN will be used for all doors. The factory default password is [0 0 0 0]. To operate door 1, you will enter [0 0 0 0][#][1] To operate door 2, you will enter [0 0 0 0][#][2] To operate door 3, you will enter [0 0 0 0][#][3] To operate door 4, you will enter [0 0 0 0][#][4] To program the keypad transmitter into the Smart ButtonTM, you must decide which door you need to operate. If you only have one Smart ButtonTM, we suggest you to use door 1. i.e. [0 0 0 0][#][1]. If you do not hear 3 beeps after entering the PIN, i.e. [0 0 0 0][#][1], that means you have entered an incorrect PIN, and the keypad transmitter will not operate your garage door. Follow the instructions below to change the PIN. To change your PIN: 1. Enter the current PIN, (factory default PIN 0 0 0 0), press * . 2. Enter new 4 to 6 digit PIN, press * . 3. Enter new PIN again, press * . For example, if you are changing the PIN number from 0000 to 123456, enter the following sequence, 0000, *, 123456, * , 123456, * . If confirmed, the backlit LED flashes and the unit emits a long beep. 5. ERASE TRANSMITTERS To erase unwanted remote control(s) from the memory of Smart ButtonTM GB-318, first erase all remote controls, then learn the one(s) you would like to keep, follow the steps below: 1. Press and hold the learn button for approximate 10 seconds. 2. The LED will flash rapidly after 10 seconds to indicate all the programmed remote controls h...