|
Anleitung Zusammenfassung
........................................................................................ 9 7 8 1 2 1 0 11 3. Remove the 3 hex head bolts 7 attached to the upper left and right door hinges with a wrench (10 mm). With a Philips head screwdriver, remove the ground screw 8 attached to the upper left and right door hinges. Remove the upper left and right door hinges 9 . 4. Lift the door straight up to remove. 5. With a Philips head screwdriver, remove the two screws 10 attached to the lower left and right door hinges. With an wrench (5 mm), remove the two hex head bolts 11 attached to the lower left and right door hinges. Remove the lower left and right door hinges 12 . REATTACHING THE REFRIGERATOR DOORS To reattach the fridge doors, assemble parts in reverse order. 1. The Water Line must be fully inserted to the center of transparent coupler (Type A) or the Guide Lines (Type B) to prevent water leakage from the dispenser. 2. Insert the clip in the install pack and check that it holds the line fi rmly. DISASSEMBLE THE FREEZER DRAWER 1. Push the upper drawer in completely. 2. Remove the tilting pocket 1 by pulling on both brackets 2 upward at the same time. 3. Take out the lower basket 3 by lifting the basket up from rail system. 4. Remove four 10 mm hex-head bolts from both sides. 5. Lift the freezer door up from the rails. Putting too much food into the freezer drawers can prevent the freezer from closing completely and can cause frost build-up. Center of Transparent coupler The Guide Lines Dispenser clip A (1/4”) (6.35 mm) clip A (1/4”) (6.35 mm) Type A Type B 8_ Setting up Slot 3 1 2 CAUTION ........................................................................................................................ ........................................................................................ 012 SOEPTETRINATGIN UGP Setting up _9 ASSEMBLE THE FREEZER DRAWER To reattach the freezer drawer, assemble parts in reverse order. ADJUSTING THE DOORS Now that the doors are back on the Refrigerator, you want to make sure the Refrigerator is level so that you can make fi nal adjustments. If the Refrigerator is not level, it will not be possible to get the doors perfectly even. Insert a fl at-blade screwdriver (-) into a notch on the left control lever, and turn it count clockwise to level the refrigerator. (You turn the lever clockwise to lower the refrigerator and counterclockwise to raise it.) Both control levers must be touching the fl oor to avoid possible personal injury or property damage because of tipping. If the right side is lower, perform the same procedure, but with the right control lever. MAKING MINOR ADJUSTMENTS BETWEEN DOORS Remember a level Refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on leveling the Refrigerator. 1. If you open the drawer 1 , you can see the lower hinge 2 . 2. Insert the supplied hex wrench 3 into the shaft 4 of the lower hinge. 3. Please adjust the height by turning the hex wrench 3 clockwise ( ) or counterclockwise ( ). When you turn the hex wrench counterclockwise( ), the door will move up. 1. After adjusting the doors, please insert the supplied fastener-ring 5 using a pair of pliers 6 in the gap between the hinge-grommet 7 and the lower hinge 8 . The number of fastener-rings you’ll need to insert depends on the gap. Two fastener-rings are enclosed with the refrigerator. The thickness of each fastener-ring is 1 mm. ADJUSTING THE FREEZER DRAWER LEVEL flfl at-blade screwdriver(-) Control Lever CAUTION When the left door is lower than the right door. When the left door is higher than the right door. Adjustment part Adjustment part 2 3 4 1 Adjustment part Freezer Drawer ........................................................................................................................ ........................................................................................ 10_ Setting up 1. Locate the height-adjuster 1 in the freezer drawer. Unscrew the four Phillips screws 2 slightly to loosen the door. 2. Loosen the controller screw 3 with a Phillips screwdriver. 3. Find the best level to align the door slope. After adjustment, fi rst tighten screw 3 and then screw 2 . CHECKING THE WATER LINE A water dispenser is one of the helpful features on your new Samsung Refrigerator. To help promote better health, the Samsung water fi lter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. In order for the ice-maker to operate properly, a water pressure of 138~862 kPa is required. Under normal conditions, a 170 cc (5.75 oz.) cup can be fi lled in 10 seconds. If the Refrigerator is installed in an area with low water pressure (below 138 kPa), you can install a booster pump to compensate for the low pressure. Make sure the water storage tank inside the Refrigerator is properly fi lled. To do this, press the water ...
Dieses Handbuch ist für folgende Modelle:Kühlen - RFG23UERS (23.27 mb)