Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
5 Press [MENU] to exit Menu mode. DOOWNEKVTSSelgnairTreggoJtfarcriApeeJemoHtaoBnoitaerceRelcihevelbatroP)tnet(raCkcurTthcaYelcycrotoMnaV APRS supports approximately 200 icons. It allows users to select each icon by specifying a combination of two ASCII codes, for example, / and !. One is a symbol code, and the other is a table identification code (either / or \). If you select “OTHERS” in step 3, you can proceed to steps for specifying combinations of two codes. This method is described in the separate manual (document file) that comes with an optional PG-4W cable. This manual describes the APRS in further details. 67 This transceiver allows you to manually enter latitude and longitude data to transmit to other stations. 1 Press [MENU] to enter Menu mode. • You may press [POS] instead. Then you can skip step 2. 2 Press [2], [3] to select “2–3 (My Pos)”. STSTA CONCON 96BCONBCONDUP 975 Grid square locator 3 Press [UP]/ [DWN] to switch between north latitude (default) and south latitude. 4 Press [OK]. • The degree digits blink. 5 Press [UP]/ [DWN] to select data for degrees. 6 Press [OK]. • The minute digits blink. 7 Repeat steps 5 and 6 to select data for minutes (down to one hundredth digit). STSTA CONCON 96BCONBCONDUP 975 8 Press [UP]/ [DWN] to switch between west longitude (default) and east longitude. 9 Press [OK]. • The degree digits blink. 10 Press [UP]/ [DWN] to select data for degrees. 11 Press [OK]. • The minute digits blink. 12 Repeat steps 10 and 11 to select data for minutes (down to one hundredth digit). STSTA CONCON 96BCONBCONDUP 975 13 Press [MENU] to exit Menu mode. Note: . If have selected “NMEA” in Menu 2–2, pressing [POS]does not allow you to access the display for entering latitude/ longitude data. The position data received via the GPS receiver most lately will be displayed. . If using a GPS receiver, you can also copy the measured data to the position entry display for Menu 2–3. Press [POS]to display the measured data, then press [OK]. “COPY to MENU?” appears. Press [OK]again. . Grid squares were developed to shortly identify locations anywhere on the Earth. The world is first divided into 324 areas (AA ~ RR) called “fields”. Each field is then divided into 100 “squares” (00 ~ 99). Each square is further divided into 576 “sub-squares” (AA ~ XX). The world is eventually divided into 18, 662, 400 grids; each grid is expressed with 6 digits. 68 SELECTING A POSITION COMMENT SELECTING A POSITION COMMENT 1 Press [MENU] to enter Menu mode. 2 Press [2], [4] to select “2–4 (POS COMMENT)”. STSTA CONCON 9696BCONDUP 975 3 Press [UP]/ [DWN] to select the desired comment. STSTA CONCON 9696BCONDUP 975 4 Press [OK] to complete the setting. 5 Press [MENU] to exit Menu mode. The selectable comments are listed below: Off Duty (default) Committed En Route Special 1 In Service Priority 1 Returning Emergency! 2 1 Selecting these comments will highlight your station on all other APRS computer displays. 2 Select this comment only when absolutely necessary. You will activate alarms in all monitoring APRS stations. 69 You can also transmit any comment (status text) with the latitude/ longitude data. If you want, enter a desired comment using a maximum of 20 alphanumeric characters. Note: Attaching a long comment can double the size and length of the packet. Enter a comment only if necessary. 1 Press [MENU] to enter Menu mode. 2 Press [2], [6] to select “2–6 (STATUS TEXT)”. • The display for entering a comment appears; the first digit blinks. STSTA CONCON 96BCONBCONDUP 975 3 Press [UP]/ [DWN] to select a character. • You can enter alphanumeric characters plus special ASCII characters. 4 Press [OK]. • The cursor moves to the next digit. 5 Repeat steps 3 and 4 to enter up to 20 digits. • Pressing [OK] after selecting the 20th digit completes the programming. • To complete programming a comment after entering less than 20 digits, press [OK] twice. • Each press of [ESC] causes the cursor to move backward. • Pressing [A/B] deletes the digit at which the cursor is blinking. 6 Press [MENU] to exit Menu mode. You can also use the keypad to enter alphanumeric characters in step 3. For example, each press of [TNC] switches entry as A, B, C, a, b, c, then 2. Press [DUAL] to switch 0 and space. Press [ENT] to switch among the special ASCII characters. 70 PROGRAMMING A GROUP CODE PROGRAMMING A GROUP CODE All calls: Program a 6-digit code that always starts with AP. You will receive all APRS packets which include AP in group codes. It does not matter whether or not the subsequent 4 digits match. The default on this transceiver is APK001; K001 stands for KENWOOD Ver.1. Note: APRS packets, which are generated via various methods, include various codes instead of group codes. Using “All calls” allows you to receive packets which include the following codes. GPS SYM QST CQ BEACON ALL SKYWRN MAIL ID SPCL Special: Enter “SPCL”. You will receive only APRS packets that include SPCL as a group code. This code is generally programmed by ...
Dieses Handbuch ist für folgende Modelle:HandFunkgeräte - TH-D7E (2.41 mb)