Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Samsung Dateigröße: 10.49 mb Dateiname: Unterrichtssprache:

If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When you install the refrigerator next to a fixed wall, you need a minimum clearance of 3 .” (95mm) between the refrigerator and wall to allow the door to swing open. First thing! Make sure that you can easily move your refrigerator to its final location by measuring doorways (both width and height), thresholds, ceilings, stairways, etc. The following chart details the exact height and depth of this Samsung French Door Refrigerator. Width Height Overall Depth “B” “C” Height “D” “E” ..35 ” (912 mm) ..68 ” (1742 mm) ..69 ” (1768 mm) 36.” (922 mm) 01 SETTING UP Model Depth “A” RF4287HA 29.” (749 mm) • Allow clearance to the right, left, back and top when installing. This will help reduce power consumption and keep your energy bills lower. EECCAABB D DD setting up _05 M DA68-01922A.indb 05 2012.5.16 2:58:42 PM • Do not install the refrigerator where the temperature will go below 50.F (10.C). • Do not locate the refrigerator where it may become wet. When moving your refrigerator To prevent floor damage, be sure the front adjusting legs are in the up position (above CAUTION the floor). Refer to ‘Adjusting the doors’ in the manual (on page 9). Control Lever Flat-blade screw driver(-) FLOORING For proper installation, this refrigerator must be placed on a leveled surface of hard material that is the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator, or approximately 359lbs (165kg). To protect the finish of the flooring, cut a large section of the cardboard carton and place it under the refrigerator where you are working. When moving a refrigerator, you need to pull and push it straight forwards or back. Do not wiggle it from side to side. ACCESSORIES AND REQUIRED TOOLS The following accessories are included with your refi gerator: Hex wrench Fastener Required Tools (Not provided) You need the following tools to complete the installation of your refirgerator: Philips screwdriver Flat-blade Socket wrench (+) screwdriver (-) (10mm) Pliers Allen wrench (3/16”) (5mm) REMOVING THE REFRIGERATOR DOORS Some installations require door removal to transport the refrigerator to its final location. Do not remove the door/drawer if you don't need to. If you do not need to remove the refrigerator doors, go to Adjusting the Level on page 8. If you need to remove the doors. continue below. Before removing the door/drawer, make sure you read the following items: Disconnect power to the refrigerator before removing the door or drawer. WARNING • Be careful not to drop, damage or scratch the door/drawer while removing them. • Be careful not to get injured while removing the door/drawer. • Reattach the door/drawer properly to avoid: - Moisture from air leakage. - Uneven door alignment. - Wasting energy due to improper door seal. 06_ setting up DA68-01922A.indb DA68-01922A.indb 06 2012.5.16 2012.5.16 2:58:43 PM 06 2:58:43 PM setting up _07 01 SETTING UP Disassemble the refrigerator doors Be careful not to drop and scratch the doors while removing the doors. Disassemble the refrigerator doors 1. With the door opened, remove the cap top table ( 1 ) with a fl at-blade screwdriver (-), and close the door. Remove the 3 screws holding down the top table ( 2 ) and turn it with several wires connected. 2. Disconnect one connector ( 3 ) on the right side door and one connector ( 4 ) on the left side door. Remove the water line ( 5 ) while pressing the dark gray color part ( 6 ) of the water line coupler. If a red clip is on the coupler, it must be removed before removing the tube. 3. Remove the 3 hex head bolts ( 7 ) attached to the upper left and right door hinges with a socket wrench (10mm). Remove the ground screw ( 8 ) attached to the upper left and right door hinges with a philips screwdriver (+). Remove the upper left and right door hinges ( 9 ). 4. Lift the door straight up to remove. 5. Remove the screw ( 10 ) attached to the lower left and right door hinges with a philips screwdriver (+). Remove the 2 hex head bolts ( 11 ) attached to the lower left and right door hinges with an allen wrench (3/16”). Remove the lower left and right door hinges ( 12 ). REATTACHING THE REFRIGERATOR DOORS To reattach the fridge doors, assemble parts in reverse order. 1. The Water Line must be fully inserted to the center of transparent coupler (Type A) or the Guide Lines (Type B) to prevent water leakage from the dispenser. 2. Insert the clip in the install pack and check that it holds the line fi rmly. WARNING CAUTION 1 2 4 5 6 Red Clip 3 (1/4") Socket wrench 7 8 9 Allen wrench 12 10 11 Center of Transparent coupler The Guide Lines Dispenser clip A (1/4”) (6.35mm) clip A (1/4”) (6.35mm) Type A Type B DA68-01922A.indb 07 2012.5.16 2:58:44 PM 08_ setting up DISASSEMBLE THE FLEX DOOR 1. Take out the Flex Zone ( 1 ) by lifting it up. 2. Take off the cover ( 2 ) w/harness with a fl at-blade screwd...

Herunterladen

Geben Sie zwei Ziffern: