Stimmen - 5, Durchschnittliche Bewertung: 3.6 ( )

Hersteller: Sears Dateigröße: 1.17 mb Dateiname: Unterrichtssprache:

Press button [] again to display a flashing MOnday__ As you did in step b above, press button 141to display ON for backwash on Monday, or OFF for no backwash on Monday. d. Press button [] for every day of the week, each time using button [] to display ON (for backwash) or OFF (no backwash) as needed. e. After setting ON or OFF for Saturday, press button [] to return the present time in the display. = SET TIME OF BACKWASH The filter is factory set to begin backwashes at 12:00 AM, ending at about 12:40 AM. If a different backwash time is desired, or needed (see note under step 3), do the following• a. Press the BACKWASH TIME button [] once, to display a flashing 12:00 AM, the factory setting• b. Press the SET/CLEAR buttonl_]untilthe desired backwash starting time shows in the display. NOTE: Press button [] and quickly release to move the display ahead 1 hour at a time. Or, hold button [] to move the display ahead 2 hours each second. C. Press button [] to return the present time. BACKWASHING GUIDE CLARIFIER FILTER The clarifier needs backwashing when you can see sediments in the water, or when faucet water pressure drops. When that happens depends on how much sediment is in the water supply,and how much water your household uses. You can use the following table as a guide. WATER CONDITION BACKWASHES PER WEEK normal sediments, dirt, etc. 1 normal sediments, _i_, etc., 2-3 WITH iron high sediments, dirt, etc. 2 high sediments, dirt, etc., 3-4 WITH iron NOTE: The timer is factory programmed for Monday, Wednesday and Saturday recharge. NEUTRALIZER/TASTE & ODOR FILTERS The filter mineral bed will trap and hold some dirt, sediments, iron, etc., that may be in your water supply. To flush them from the mineral bed, 1 backwash each week is recommended. Backwash also stirs the mineral bed which helps to keep water flowing through the entire bed instead of forming a channel. 8 SECTION 2 HOW YOUR WATER FILTER WORKS II 2A. FACE PLATE TIMER FEATURES BACKWASH NOW For times you expect to use more water than usual, use the BACKWASH NOW feature. Press the BACHWASH NOW-HOLD button [] and hold in for 3 seconds. RCHG begins to flash in the display and a backwash starts right away. You will have filtered water when the backwash is over in about 35 minutes. _) PRESENT TIME AND DAY _ BACKWASH DAY SET!CLEAR ONIOFF VACATION HOLD BACKWASH NOW VACATION --The day you leave on vacation, or other long absence, press (DO NOT HOLD IN) the ON/OFF-VACATION button []. VAC begins to flash in the display (FIG. 4). The timer will keep time, but the filter will not backwash and waste water. NOTE: To shut off the water supply to the filter, use the plumbing bypass valve(s)... FIG. 8, page 18. When you return, press the VACATION button again to return the filter to service, and the correct time of day in the display. Remember to do this or the filter will not backwash to keep the mineral bed clean. _ PRESENT TIME AND DAY _ BACKWASH DAY _ SET/CLEAR _ ON/OFF VACATION HOLD BACKWASH NOW ERROR CODE An error code could appear in the faceplate if a problem occurs in the filter elec-I display instead of the present time of day, please call your local Sears Service Department for service. tronics. If you see an error code I !_-_ Continued 9 SECTION 2 HOW YOUR WATER FILTER WORKS I 2A. FACE PLATE TIMER FEATURES TIMER "POWER-OUTAGE MEMORY" --If electrical power to the timer goes off, the "memory" built into timer circuitry keeps all settings for 5 hours (minimum) or more. The display is blank and the filter will not backwash. When electrical power comes on, 1 of 2 things will happen. 1. The present time of day will show, meaning the timer mem...

Herunterladen

Geben Sie zwei Ziffern: