With knot to right side, place smaller log piece (#5) over the pin on the left side of the middle log. The smaller log will rest on front log against the "knot" on the left. See Figure 27. 6. Place lava rock around base of heater if desired. Do not put lava rock on logs on burner. Recess INSTALLATION Installing Logs (Cont.) 107124-01E Forr morre iinfforrmattiion,, viisiitt 16 Dual Burner Biltmore Split Oak Models WARNING: Failure to position the parts in accordance with these diagrams or failure

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases. 2. Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors (propane/LP units only). 3. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity (propane/LP units only). 4. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any elect

If so, you must always run heater with chimney flue damper open. If running heater with damper open, noncombustible material above fireplace opening is not needed. Go to Installing Damper Clamp Accessory for Vented Operation,page 10. Minimum Noncombustible Material Clearances If Not Using Mantel Note:If using a mantel, proceed to If Using Mantel. If not using a mantel, follow the information below. You must have noncombustible material(s) above the fireplace opening. Noncombustible materials (su

Flames contacting logs will create soot. Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater. 1. Place the front log (#1) on the grate fingers. Make sure the front log rests firmly between the grate fingers and the grate base (see Figure 24). Figure 24 - Installing Front Log #1 (CCL3930PTB/NTB Shown) Front Log (#1) Grate Fingers Grat

The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc. Note: Selecting the HI setting with the control knob will cause the burners to remain fully on, without modulating down in most cases. 1. Follow steps 1 through 5 under Lighting Instructions, page 19. 2. Depress control knob and light pilot with match. 3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control

If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly. 1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes. 2. Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 41). 3. Blow air through the ports/slots and holes in the burner. Figure 41 - Injector Holder On Outlet Burner Tube Ports/Slots Burner Tube Pilot A

When ordering parts, follow the instructions listed under Replacement Parts on page 28 of this manual. KEY NO. PART NUMBER DESCRIPTION QTY.CCL3018PTA CCL3018NTA 1 111340-03 111340-03 Front Log (#1) 1 2 111341-03 111341-03 Middle Log (#2) 1 3 111342-03 111342-03 Back Log (#3) 1 4 111343-03 111343-03 Left Back Crossover Log (#4) 1 5 111344-02 111344-02 Left Top Crossover Log (#5) 1 6 111345-02 11345-02 Right Bottom Crossover Log (#6) 1 7 102775-09CK 102775-09CK Painted Base Assembly 1 8 102844-02

8.0" W.C. 3.5" W.C. 8.0" W.C. Inlet Gas Pressure (in. of water) Maximum 10.5" 14" 10.5" 14" Minimum* 5" 11" 5" 11" Shipping Weight 36 lbs. 38 lbs. * For the purpose of input adjustment DUAL BURNER BILTMORE SPLIT OAK MODELS CCL3018PTA CCL3924PTA CCL3930PTB CCL3018NTA CCL3924NTA CCL3930NTB Btu (Variable) 16,000/30,000 20,000/39,000 20,000/39,000 Type Gas Natural Propane/LP Natural Propane/LP Natural Propane/LP Ignition Piezo Piezo Piezo Manifold Pressure 3.5" W.C. 8.0" W.C. 3.5" W.C. 8.0" W.C. 3.5

In the event of a power outage, you can use this heater as your primary heat source. WARNING: A qualified service person must install heater. Follow all local codes. NOTICE: State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes. WARNING: Before installing in a solid fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes, and loose paint by a qualified chimney cleaner. Creosote will ignite

See Figure 30 for CCL3924PTA/NTA or CCL3930PTB/ NTB. See Figure 29, page 15, for CCL3018PA/NA or CCL3018PTA/NTA. 7. For CCL3930PTB/NTB only: Locate holes on the bottom of crossover log (#7). Slide onto the pins located in crossover log (#6) and middle log (#2). See Figure 31. 8. Add lava rock around base of heater if desired. Do not place any lava rock on logs or burner. Crossover Log (#6) Crossover Log (#7) 111160-01B Forr morre iinfforrmattiion,, viisiitt 1177 INSTALLATION Installing Logs (Con