Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Enerco Dateigröße: 302.36 kb Dateiname: Unterrichtssprache:

Forced Air means that a blower or fan pushes the air through the heater. Proper combustion depends upon this air flow; therefore, the heater must not be revised, modified or operated with parts removed or missing. Likewise, safety systems must not be circumvented or modified in order to operate the heater. When the heater is to be operated in the presence of other people the user is responsible for properly acquainting those present with the safety precautions and instructions, and of the hazards involved. Enerco Group, Inc.| Forced Air Propane Construction Heater 3 Operating Instructions and Owner’s Manual SAFETY PRECAUTIONS 1. Check the heater thoroughly for damage. DO NOT operate a damaged heater. 2. DO NOT modify the heater or operate a heater which has been modified from its original condition. 3. Use only propane gas. 4. Use only VAPOR WITHDRAWAL propane supply. If there is any question about vapor withdrawal, ask your propane dealer. 5. Mount the propane cylinders vertically (shutoff valve up). Secure them from falling or being knocked over and protect them from damage. 6. Locate propane containers at least (USA) 7 ft. (2.13m), (Canada) 10 ft. (3m) from the heater and do not direct exhaust toward containers. 7. IMPORTANT Use only the hose and regulator assembly provided with the heater. Match the color stripe on the hangtag attached to the hose assembly with the color on the label located near the propane inlet fitting on the heater. Inspect hose assembly before each use of the heater. If there is excessive abrasion or wear, or hose is cut, replace with hose assembly listed on parts list before using heater. 8. For indoor use only. Area must be well ventilated. Figure 1. (also see "Operating Precautions"). 9. If at any time gas odor is detected, IMMEDIATELY DISCONTINUE operation until the source of gas has been located and corrected. Read enclosed Odor fade and Propane Sheet for additional information about detecting propane leaks. 10. Install the heater such that is is not directly exposed to water spray, rain and/or dripping water. 11. Maintain minimum clearance from normal combustible material (like paper). Figure 2. 12. Due to the high surface and exhaust temperatures, adults and children must observe clearances to avoid burns or clothing ignition. 13. Operate only on a stable, level surface. 14. Do not use with ductwork. Do not restrict inlet or exit. 15. Use only the electrical power specified. The electrical connection and grounding must comply with National Electrical Code - ANSI/NFPA 70 (USA) and CSA C22.1 Canadian Electrical Code, Part 1 (Canada). 16. Use only a properly grounded 3-prong receptacle or extension cord. 17. Do not move, handle or service while hot or burning. 18. Do not adjust the heater combustion tube elevation while heater is running or hot. Adjustments to elevation should only be made after the heater has cooled to touch. 19. Use only in accordance with local codes or, in the absence of local codes, with the Standard for the Storage and Handling of Liquefied Petroleum Gases ANSI/NFPA 58 and CSA B149.1, Natural Gas and Propane Installation Code. Figure 1 VENTILATION: Minimum openings required Opening Opening Heater near floor near ceiling Forced air (55) .................... 1 ft2 .......................................... 1 ft2 Forced air (85, 125) ............ 2 ft2 .......................................... 2 ft2 Figure 2 MINIMUM CLEARANCE: From normal combustible material Clearance 55, 85, 125 Forced Air From floor ........................................ 0 ft From outlet ....................................... 6 ft From sides ........................................2 ft From top...........................................3 ft Locate 10 ft. from canvas or plastic ...

Herunterladen

Geben Sie zwei Ziffern: