Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Canon Dateigröße: 4.37 mb Dateiname: Unterrichtssprache:

CHG (charge) DC IN terminal indicator 3 Connect the power cord to the compact power adapter. 4 Plug the power cord into a power outlet. 5 Connect the compact power adapter to the camcorder’s DC IN terminal. • The CHG (charge) indicator starts flashing. The indicator will stay on when the charging is completed. • If the indicator flashes quickly, refer to Troubleshooting ( 99). ONCE THE BATTERY PACK IS FULLY CHARGED 1 Disconnect the compact power adapter from the camcorder. 2 Unplug the power cord from the power outlet and the compact power adapter. 20 TO REMOVE THE BATTERY PACK BATTERY RELEASE switch 1 Slide BATTERY RELEASE in the direction of the arrow and hold it pressed down. 2 Slide the battery pack down and then pull it out. IMPORTANT • Turn off the camcorder before connecting or disconnecting the compact power adapter. After pressing ON/OFF to turn off the camcorder, important data is updated in the memory. Be sure to wait until the indicator turns off. • We recommend charging the battery pack in temperatures between 10 °C and 30 °C (50 °F and 86 °F). Outside the temperature range of 0 °C to 40 °C (32 °F to 104 °F), the charging will not start. • Do not connect to the camcorder’s DC IN terminal or to the compact power adapter any electrical equipment that is not expressly recommended for use with this camcorder. • To prevent equipment breakdowns and excessive heating, do not connect the supplied compact power adapter to voltage converters for overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc. NOTES • If remaining battery time is an issue, you can power the camcorder using the compact power adapter so the battery pack will not be consumed. • Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day before, to ensure a full charge. • We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need. • U.S.A. and Canada only: The lithium ion/polymer battery that powers this product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery. Preparations Preparing the Wireless Controller and Accessories First, insert the supplied lithium button battery CR2025 into the wireless controller. Tab 1 Press the tab in the direction of the arrow and pull out the battery holder. 2 Place the lithium button battery with the + side facing up. 3 Insert the battery holder. TO USE THE WIRELESS CONTROLLER Point the wireless controller at the camcorder’s remote sensor when you press the buttons. You can rotate the LCD panel 180 degrees to use the wireless controller from the front of the camcorder. NOTES • The wireless controller may not work properly when the remote sensor is situated under strong light sources or direct sunlight. • If the wireless controller does not work, check that [WL.REMOTE] is not set to [ OFF ] ( 96). Otherwise, replace the battery. Accessories 2 Pull the strap to remove it first Fasten the grip belt. • Adjust the grip belt so that you can reach the zoom lever with your index finger, and the START/STOP button with your thumb. • You can remove the grip belt and replace it with the supplied wrist strap. TO REMOVE THE GRIP BELT 1Lift the padded handgrip's flap and detach the strap from the Velcro pad. from the front bracket on the camcorder, then to unthread it from the handgrip and finally to remove it from the rear bracket on the camcorder. TO ATTACH A WRIST STRAP Pass the attaching end of the wrist strap through the back bracket on the camcorder, thread the wrist strap through the loop and fasten. You can also attach the wrist strap to the strap mount on the grip belt to use both for extra convenience and protection. 23 Subject can monitor the LCD screen 180° 90° 180° Preparations TO ATTACH A SHOULDER STRAP Pass the ends of the shoulder strap through the strap mount on the grip belt and adjust the length of the strap. You can also remove the grip belt and attach the shoulder strap directly to the rear bracket on the camcorder. TO REATTACH THE GRIP BELT 1 Pass the end of the strap through the rear bracket on the camcorder. 2 Thread the strap through the padded handgrip and then pass it through the front bracket on the camcorder. 3 Fasten the grip belt as necessary, attach the strap to the Velcro pad on the handgrip and close the flap. Adjusting the Position and Brightness of the LCD Screen Rotating the LCD Panel Open the LCD panel 90 degrees. • You can rotate the panel 90 degrees downward. • You can rotate the panel 180 degrees toward the lens. Rotating the LCD panel 180 degrees can be useful in the following cases: -When you wish to include yourself in the picture when recording with the self timer. -To allow the camcorder to be operated with the wireless controller from the front. 25 NOTES About the LCD screen: The screen is produced using extremely high-precision manufacturing techniques, with more than 99.99% of the pixels operati...

Herunterladen

Geben Sie zwei Ziffern: