Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: JVC Dateigröße: 2.91 mb Dateiname: Unterrichtssprache:

If you have a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set “L-2 SELECT” back to “DECODER” after editing. . If you’re not connecting a decoder to the AV2 (L-2) IN/ DECODER connector, leave “L-2 SELECT” set to “L-2”. . The default setting is “L-2”; if the recorder’s memory backup has expired due to a power cut or because the AC was removed from the recorder, “L-2” will be automatically selected when the power is restored to the recorder. If you are using a decoder, be sure to set “L-2 SELECT” back to “DECODER”. . When “L-2 SELECT” is set to “SAT”, “SAT” appears on the screen or front display panel instead of “L-2”. You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM* signals on this recorder. Select the appropriate colour system. * SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video cassette recorder. NOTES: About NTSC Playback . Some TVs shrink the picture vertically and place black bars at the top and bottom of the TV screen. This is not a malfunction on the part of either the video recorder or the TV. . The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.) . The counter and tape remaining time readings will be incorrect. . During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour. . Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback. 40 EN SUBSIDIARY SETTINGS (cont.) IMPORTANT Perform the following steps only if — Tuner Set Turn on the TV and select the video channel (or AV mode). — Auto Channel Set has not been set correctly by Auto Set Up or by Preset Download (. pg. 8, 10). — you have moved to a different area or if a new station starts broadcasting in your area. Your recorder needs to memorize all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR buttons without going through any vacant channels. Auto Channel Set A A Turn on the recorder. Press 1. B B Access the Main Menu screen. Press MENU. C C Access the Auto Channel Set screen. Press rt to move the highlight bar (pointer) to “AUTO CH SET”, then press OK or e. D D Select your country. Press rt to move the highlight bar (pointer) to your country’s name, then press OK or e. E E Select the language. Press rt to move the highlight bar (pointer) to the language of your choice. EN 41 IMPORTANT . In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the recorder will record a TV programme of a different station. When programming the timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly (. pg. 24, “SHOWVIEW® Timer Programming”). . Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture (. pg. 43, “Delete A Channel”). NOTES: . Fine tuning is performed automatically during Auto Channel Set. If you want to perform it manually, refer to page 44. . If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED -NO SIGNAL-” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again. . If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels (. pg. 43, “INFORMATION”). F F Perform Auto Channel Set. Press OK twice. . If you have connected the recorder and your TV via AV connection (. pg. 7), the recorder automatically performs the Preset Download and the T-V LINK screen will appear (. pg. 10). . The Auto Set screen appears, and remains on screen while the recorder searches for receivable stations. As Auto Channel Set progresses, the “q“ mark on the TV screen moves from left to right. Wait until the TV screen as shown in step 7 appears. Beginning End G G View the Confirmation screen. After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen — channel positions (PR), channels (CH) and station names (ID – . pg. 45). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rt w e button...

Herunterladen

Geben Sie zwei Ziffern: