Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
To copy from one VCR to another VCR 1 Press the AVX button on the remote control of VCR-1 so that L1 (line) appears in the display. 2 Press the REC, then PAUSE buttons on VCR-1. The VCR will go into Record/Pause. 3 Press the PLAY button on VCR-2. You will see the taped program being played on the TV. 4 When you see the part of the program you wish to record, press the PAUSE button on VCR-1 again to release pause and start recording. . Press the STOP button to finish recording. PROBLEM GUIDE / MAINTENANCE PROBLEM GUIDE / MAINTENANCE Problem guide No power . Make sure the VCR is plugged into an AC outlet. Remote control doesn’t work . Make sure the batteries are fresh, and properly installed. Won’t record . Safety tab has been removed from cassette (VCR will automatically eject the tape). Won’t play back . Make sure the TV/VCR switch is set to the VCR mode. . Make sure the TV is set to the VCR channel (3 or 4) or AUX (if using direct audio/video hookup). Won’t make timer recordings . The VCR power must be turned off to activate timer recording. . Clock is not set correctly. . Programs entered incorrectly. . Programs exceed the length of the cassette. Use the EP recording speed for maximum programming. . Safety tab has been removed from cassette. Snowy picture in playback . Snow or picture noise is normal during search, still, and slow Playback. . Head cleaning may be required. . Tape is worn or of inferior quality - adjust tracking controls. Snowy picture in normal TV viewing . Check antenna or cable connections. Clock shows --:-- on the TV display . Power has been interrupted - reset the clock. . Reset the clock. Erratic VCR display . Push the reset switch with a sharp pointed instrument (pen, toothpick, etc.). Maintenance Regular periodic maintenance is required to maintain optimum VCR performance. Such maintenance and adjustments should not be attempted by the user. Please consult your service dealer for further information. NOTE: Dirt accumulation on the video heads will cause the playback picture to become noisy. The VCR may require the video heads to be professionally cleaned by a qualified service dealer. Guide indications in VCR display and OSD screen The following indications appear in the VCR display and OSD screen to tell you the current status of your VCR. Guide indications in VCR display and OSD screen The following indications appear in the VCR display and OSD screen to tell you the current status of your VCR. ODS Indication When it appears Meaning andtroubleshooting (flashes for about 5 seconds) When programming the timer . The VCR clock has been set to "--:--". Set the time and program the timer. (flashes for about 5 seconds) When programming the timer (by using VCR display) . A non-existing PlusCode number has been entered. Check the PlusCode number of the program and enter it again. (flashes for about 5 seconds) When programming the timer . Eight programs have already been stored. Cancel unnecessary program and transfer the new program. (flashes uninterruptedly) When you turn power off after programming the timer, or transfer the programming with the power off . A cassette has not been inserted or a cassette without safety tab has been inserted. A cassette without safety tab will be ejected automatically. Insert a cassette with safety tab intact.. Display for about 5 sec. (flashes for about 3 seconds) When you press the play, record, fast forward, rewind or super index button . A cassette has not been inserted. Insert a cassette. Display for about 5 sec. (flashes for about 3 seconds) When you press the record button for recording or dubbing, or press the (VIEW/SKIP/BLAN K) button for BLANK SEARCH . A cassette without safety tab has been inserted. It will be ejected automatically. Insert a cassette with safety tab intact.. (flashes for about 3 seconds) When you turn power on . The video heads are dirty. Cleaning them is recommended. To switch off the CL display, clean the heads, turn the power off and press the channel button. The CL display automatically switches off when recording and playback are performed for about 5 hours after it appears. TECHNICAL SPECIFICATIONS Format: VHS Video Signal System: NTSC color EIA standard Record/Playback System: Video: 4 head Audio: VHS Hi-Fi stereo record/playback system Tape Speed: 33.35 mm/sec (SP), 16.67 mm/sec (LP) (playback only), 11.12 mm/sec (EP) RF Input: UHF/VHS 75 ohm Tuner: USA: 181 channel tuning ability* (125 cable channels) Canada: 178 channel tuning ability* (122 cable channels) Type: Auto programming frequency synthesis Power Input: AC 120V 60 Hz Power Consumption: 16W nominal 2.0W (Standby mode) Cabinet Size: 14-15/16" (W) x 3-11/16" (H) x 10-13/16" (D) 38.0 cm (W) x 9.3 cm (H) x 27.5 cm (D) Weight: 7.7 lbs. (3.5 kg) Storage Temperature: -4°F to 131°F Operating Temperature: 41°F to 104°F Accessories: 1 coaxial cable (Part No. EW10251) 1 remote control unit (Part No. HL11131) for VT-FX6410A, 2 AA batteries 1 remote control unit (Part No. H...
Dieses Handbuch ist für folgende Modelle:Kameras - VT-FX6411A (2.11 mb)