Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Hitachi Dateigröße: 2.11 mb Dateiname: Unterrichtssprache:

If any are missing or appear damaged, consult your dealer. Remote Control Cable for connecting Batteries for remote this VCR to a TV control handset (R6) VCR Customer Controls Item No. Function 21 22 23 AUDIO IN L, R jacks VIDEO IN jack IN FROM ANT. -signal input 24 OUT TO TV - signal out to TV 25 VIDEO OUT jack 26 AUDIO OUT L, R jacks Remote Control Customer Controls Item No. Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Transmission window POWER button CH (channel up/down) button VOL button - increase or decrease the audio volume Cursor buttons REW button - fast rewind or search REC - record button GUIDE - to recall OSD menu DISPLAY- to recall on-screen display PROGRAM (programming) button CLEAR - clears time counter 100/ENT button VCR/TV mode select button TAPE SPEED button - select the recording speed SP or EP VCR, TV, CATV - Device buttons let you set the remote to control one of the three devices. SUPER INDEX buttons - to use the SUPER INDEX function PLAY button - playback PAUSE/ENTER buttons 19 20 21 22 23 24 25 F.FWD button - fast forward or search SLOW button - for slow motion picture STOP button - stops play/record function Number buttons AVX button - select L1 or L2 LAST CH button - Switches to the TV channel you watched previously during the current viewing session. F.ADV button VT-FX6411A only When you press any of illumination buttons, the illumination will turn on. The illumination goes off 5 seconds later automatically, if you do not press the buttons. REMOTE OPERATION Install batteries in the remote control The remote control requires two "AA" batteries. 1 Insert your fingertip into the notch and push the battery compartment lid to remove it. Note: When replacing the batteries, remove the old batteries and keep the POWER button depressed for 10 seconds before inserting fresh batteries. Hold for 10 Seconds 2 Install batteries. . Align the positive (+) and negative (-) polarity marks on the batteries with those indicated on the remote control. 3 Replace the lid. Operating in the remote control Operating the VCR: 1 Make sure there is no obstacle between the remote control and VCR's infrared receiver. Note: You cannot operate the VCR if there is an obstacle (for example, coffee table, sofa, etc) between the VCR and remote control. 2 Point the remote control at the VCR's infrared receiver and press the required buttonon the remote control. Note: If the remote does not work even at close range, try replacing the batteries with two fresh "AA" batteries. CASSETTE TAPES Types Only use video cassettes with the mark in this VCR. The table shows the recording time of different cassettes. . To get the best quality picture record at standard recording speed (SP) . This VCR does not record at the LP speed, but it can play cassette that were recorded at the LP speed. Safety tabs prevent erasure The VCR automatically enters the playback mode when a cassette without its safety tab is inserted. The VCR won't record on a tape without a safety tab and the cassette will be ejected if the REC or REC/IRT button is pressed. Be sure to check the safety tab before inserting a cassette. Insertion Push the video cassette gently into the slot on the front of the VCR. . The VCR automatically turns on and the "Tape-In" indicator turns on when the cassette is in place.. Removal Press the STOP/EJECT button on the VCR. The cassette will come partially out of the compartment so you can pull it out. . The "Tape-In" indicator turns off. . The cassette can be ejected with the power on or off. BASIC ANTENNA HOOKUP [A] BASIC ANTENNA HOOKUP [A] WITH THIS HOOKUP YOU CAN... . WATCH AVAILABLE TV CHANNELS • RECORD AND WATCH THE SAME CHANNEL • RECORD ONE CHANNEL AND WATCH ANOTHER Caution: Do not connect to the mains supply socket before connecting all leads (ss page 17). Basic Hookup with Antenna: RF Hookup * PURCHASED SEPARATELY Switch the RF Channel When the VCR is on, its video signal can come into your TV on either channel 3 or channel 4. You need to select the appropriate channel. . When the power is turned on, press the POWER button to turn it off. Press the PLAY button on front of the VCR. Pressing the CHANNEL button alternates between RFCH-03 (channel 3) and RFCH-04 (channel 4) in the VCR’s display. Display the channel which is not used by a commercial channel in your area. ADVANCED ANTENNA HOOKUP -AV HOOKUP [B] WITH THIS HOOKUP YOU CAN... . WATCH AVAILABLE TV CHANNELS • RECORD AND WATCH THE SAME CHANNEL • RECORD ONE CHANNEL AND WATCH ANOTHER Caution: Do not connect to the mains supply socket before connecting all leads (ss page 17). * PURCHASED SEPARATELY BASIC CABLE HOOKUP [C] WITH THIS HOOKUP YOU CAN... . WATCH AVAILABLE CABLE CHANNELS • RECORD AND WATCH THE SAME CHANNEL • RECORD ONE CHANNEL AND WATCH ANOTHER Caution: Do not connect to the mains supply socket before connecting all leads (ss page 17). Switch the RF Channel When the VCR is on, its video signal can come into your TV on either channel 3 or channel 4. You ...

Herunterladen

Geben Sie zwei Ziffern: