Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Best Dateigröße: 1.67 mb Dateiname: Unterrichtssprache:

/ 0 () 0 • Run black (live), white (neutral), and green (earth) wires (#14 AWG) according to the National Electrical Code or CSA Standards and local codes and ordinances in 1/2” conduit from power supply to j-box. • Connect black, white, and green wires from power supply to black, white, and green/yellow wires in j-box respectively. • These connections should be done always making reference to the electrical diagram found inside the hood. • Close j-box cover and reapply screws. Mounting the glass canopy • With the hood mounted on the wall slide the glass canopy over the glass supports. • Insert the glass brackets. • Insert two screws into the bracket holes, drive the screws by hand. Installing the hood 14 Mounting the duct cover • Position the duct cover over the mounted hood. • Slide the bottom of the duct onto the glass area. • Position the top of the duct over the duct mounting bracket. If a telescopic duct cover is used, grab the upper part of the telescopic duct cover, pull it and place it in the duct cover mounting bracket. • Secure the top of the duct with 2 assembly screws provided. • Secure the bottom of the duct with 2 assembly screws provided. Install the grease filter and turn power on at service panel. Check operation of the hood. IMPORTANT: If the hood doesn’t switch ON, before calling for service, check if the internal General ON/ OFF Pushb-utton Switch is switched ON. Installing the hood General ON/OFF Push button Switch Back side of the hood Frontside of the hood Features Features 1. 1.1.1.1. 1. Blower and light controls 2. 2.2.2.2. 2. Lamp housings 3. 3.3.3.3. 3. Grease filter Handle 4. 4.4.4.4. 4. Grease filter 5. 5.5.5.5. 5. Canopy 6. 6.6.6.6. 6. Duct cover 7. 7.7.7.7. 7. Louver holes (Only for Recirculating version) 16 Control buttons Control buttons This hood is equipped with an electronic motor and lamp control. The control is able to set 4 different fan speeds, turn ON/OFF light and has a timer function. In the following drawing are described the main key functions. 1. Light Button • Press lamp button to turn ON the light (Lamp state previously OFF). • Press lamp button to turn OFF the light (Lamp state previously ON). 2. Timer Button • The default timer setting is 10 minutes, and it can be adjusted between 20 minutes and 1minute. • After pressing the timer button, the control enters to a timer setup mode, and user can adjust the timer countdown time with the “ ” and “ ” buttons within 5 seconds. The timer can be initiated immediately pressing the timer button, after setting the timer duration or pressing the timer button twice (default 10 minutes setting). • If no action occurs within 5 seconds, the countdown will start. • During the timer setup the “ ” and “ ” buttons are dedicated to the timer and no motor action will occur. • Once the timer is initiated, it can be cancelled by pressing the timer button again. 3. Display • Shows the hood settings. 4. “ ” Button. Speed Decrease / OFF • This button is used to decrease the fan speed, or turn OFF the fan. • The fan will turn OFF if the “ ” button is pressed and the hood was in the first speed. • If the fan is at second speed and the “ ” button is pressed, the fan will be set to first speed. • If the fan is at third speed and the “ ” key is pressed, the fan will be set to second speed. • If the fan is at fourth speed and the “ ” button is pressed, the fan will be set to third speed. • If the fan is OFF and the “ ” button is pressed, the control backlight will light up. 5. “ ” Button. Speed Increase / ON • This button is used to increase the fan speed, or turn ON the fan. • The fan will turn ON if the “ ” button is pressed and the hood was OFF. • If the fan is at first speed and the “ ” button is pressed, the fan will be set to second speed. • If the fan is at second speed and the “ ” button is pressed, the fan will be set to third speed. • If the fan is at third speed and the “ ” button is pressed, the fan will be set to fourth speed. • If the fan is at fourth speed and the “ ” button is pressed, a beep will sound. IMPORTANT: If the hood doesn’t switch ON, before calling for service, check if the internal General ON/ OFF Pushb-utton Switch is switched ON. General ON/OFF Push button Switch Back side of the hood Frontside of the hood Control buttons - Special functions Special functions Clock pr Clock prClock prClock prClock prClock programming ogrammingogrammingogrammingogrammingogramming • The clock can be reprogrammed at any time except during an active timed function. • The clock can be displayed in a twelve hour format and valid clock times are from 1:00 to 12:59...

Herunterladen

Geben Sie zwei Ziffern: