Stimmen - 6, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Desa Dateigröße: 1.14 mb Dateiname: 109493-01N.pdf Unterrichtssprache:

WARNING: If the fireplace has been used for wood burning, the firebox and chimney must be cleaned of soot, creosote and ashes by a qualified chimney cleaner. Creosote will ignite if heavily heated. WARNING: When using a decorative vented gas log, the damper must be removed or permanently locked in the fully open position and the glass doors must be in the fully open position. Optional Gas Line Installation Continued Glass Door Installation IMPORTANT: Install glass door frame before installing glass door. Installing Door Frames 1. Remove screws from smoke shelf (see Figure 20). 2. Mount top door frame and secure with screws removed in step 1. 3. Remove center brick by pulling ring handle (see Figure 21). 4. Remove ash box. 5. Remove three screws located at front of firebox (see Figure 21). 6. Align bottom rail mounting holes with holes at front of firebox and secure with screws removed in step 5. 7. Place ash box in place. Replace center brick. Top Door Frame Smoke Shelf Figure 20 - Installing Top Door Frame Bottom Door Rail Ash Box Center Brick Screws Ring Handle Figure 21 - Installing Bottom Door Frame Installing glass doors Spring clips have been installed but some adjustments may be needed. If doors do not close properly or do not appear straight, see Door Adjustment. 1. With bi-fold doors completely folded, insert bottom pivot pin into pivot hole located near bottom corner of front face opening and swing door to vertical position making sure top pins slide into door track. Door is installed when top door pin snaps into spring clip. 2. Repeat step 1 for remaining door. If you find the doors do not close properly or do not appear level or straight, proceed with section on door adjustment, Door Adjustment Remove doors and slightly loosen lower pivot clips and upper spring clips. Replace doors and fully close them. Use 1/8" shims (any material) to level doors. Once proper setting is achieved, carefully open doors enough so that you can access spring clips with a phillips screwdriver. Tighten screws. See Figure 23. Glass Door Installation Continued Operation and Maintenance Guidelines Glass Doors Glass doors are optional with the fireplace. When fireplace is in operation, doors must be fully opened or fully closed position only or a fire hazard may be created (see Figure 24). A fireplace equipped with glass doors operates much differently than a fireplace with an open front. A fireplace with glass doors has a limited amount of air for combustion. Excessive heat within the fireplace can result if too large a fire is built or if combustion air gate is not completely open. The following tips should be followed to assure that both the fireplace and glass door retain their beauty and function properly. Both the flue damper and glass doors must be fully opened before starting fire. This will provide sufficient combustion air and maintain safe temperatures in firebox. IMPORTANT: The glass must be allowed to warm slowly and evenly. The tempered glass will withstand a gradual temperature rise to 550° F, which is more than a normal fire will generate. Such materials as pitch/wax laden logs, very dry mill end lumber and large amounts of paper or cardboard boxes can create an excessively hot fire and should not be burned in this fireplace. Always keep the fire well back from the doors and never allow flames to contact the glass. WARNING: Fireplaces equipped with glass doors should be operated only with doors fully opened or doors fully closed. Doors, if left partly open, may draw gas and flame out of the fireplace opening creating risks of both fire and smoke. Spring Clip Fold Door and Slide Top Pins Into Track Insert Pin into Spring Clip Insert Bottom Pivot Pin into Hole Pivot Hole Figure 22 - Installing Bi-Fold Doors Spring Clip Doors Fully Closed Fireplace Front Fireplace Front Doors Fully Opened Figure 23 - Adjusting Bi-Fold Doors Figure 24 - Bi-Fold Glass Doors Cleaning Glass Clean glass with any commercial glass cleaner or soap and water. Do not use any abrasive material to clean glass. Do not clean glass with any cool water if glass is still hot from the fire and smoke. A gas line or gas log lighter may be installed for the purpose of installing a vented or vent-free decorative gas appliance incorporating an automatic shutoff device and complying with the Standard for Decorative Gas Appliances for Installation in Vented Fireplaces, ANSI Z21.60 or American Gas Association draft requirements for Gas Fired Log Lighters for Wood Burning Fireplaces, Draft NO. 4 dated August, 1993. If you wish to install an unvented (vent-free) gas log set, only unvented gas log sets which have been found to comply with the standard for unvented room heaters, ANSI Z21.11.2 are to be installed in this fireplace. outside air and damper handle operation The damper handle, which opens and closes the damper blade, is located in the upper front face of the fireplace. Pushing the handle forward and up through the keyway slot will free damper ...

Herunterladen

Geben Sie zwei Ziffern: